manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–902

INSPECTION PROCEDURE: P1530

1.

Check the installation of the engine stop switch.

NO

YES

1.

Check the connection of the engine stop switch connector (Loose-
ness and poor contact).

NO

YES

1.

Set the starter switch to the "LOCK" position.

2.

Disconnect the engine stop switch connector.

3.

Use the electrical tester to perform a unit test of the engine stop
switch.

NO

YES

1

Inspect the engine stop switch

Was any failure found?

Install the engine stop switch correctly.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

2

Inspect the engine stop switch connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 3.

3

Inspect the engine stop switch unit

Was any failure found?

Replace the engine stop switch.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 4.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Back View RV-250 User Manual preview
RV-250
Brand: Back View Pages: 168
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Brand: RAM Pages: 16
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Brand: Saleen Pages: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Brand: Buick Pages: 5
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Brand: Mercedes-Benz Pages: 388
Standby L54 Manual preview
L54
Brand: Standby Pages: 10
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Brand: Monacor Pages: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Brand: Jeep Pages: 338
Axxess AX-LR904 Installation Instructions Manual preview
AX-LR904
Brand: Axxess Pages: 8
SeaSucker SX6150 Quick Start Manual preview
SX6150
Brand: SeaSucker Pages: 9
STC 552-010 Installation Instructions Manual preview
552-010
Brand: STC Pages: 6
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Brand: Voxoa Pages: 48
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Brand: mtf TRANSPORT SYSTEM Pages: 9
Bestop Bikini Installation Instructions preview
Bikini
Brand: Bestop Pages: 5
PowerMadd Tri-mount Installation Instructions preview
Tri-mount
Brand: PowerMadd Pages: 3
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Brand: Cadillac Pages: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Brand: TIE DOWN Pages: 2
iDataLink ADS-TBSL-GM Install Manual preview
ADS-TBSL-GM
Brand: iDataLink Pages: 6

Brands by name

Popular brands

Load more brands