manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1009

DTC: P2138

EN01H16F01030F03001130

P2138: Accelerator pedal position sensor - rationality

INFORMATION

1. Technical description

<Description of malfunction>

•

Abnormal characteristics or stuck sensing of accelerator sensor

2. DTC set condition

(1) Check conditions

•

Starter switch ON.

•

Battery voltage is in the range of 10 V to 16 V.

•

The engine has stopped (stalled) or runs at 500 r/min or higher for continuous 5 seconds or longer.

(2) Judgement criteria

Comparison of sensor voltage between sensor 1 and sensor 2

•

Accelerator pedal position sensor 2 voltage 

–

 Accelerator pedal position sensor 1 voltage. 

≤

 0 V or 

≥

 1.6 V

•

Failure timer 

≥

 3 seconds

3. Reset condition

•

Immediately after normal operation is restored.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Cruise control function is not available.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Cruise control does not work.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

8. Estimated failure factors

•

Harness disconnection or short-circuit

•

Malfunction of accelerator sensor

•

Malfunction of engine ECU

Accelerator
sensor

Engine 

ECU

K5Z

(ACS1)

K8Z

(GND1)

(SIG1)

KRS

(AVC4)

LCS

K91

(ADG8)

(VCC2)

(GND2)

K62

K92

(ACS2)

(SIG2)

KRR

K8Y

(AVC3)

(VCC1)

LCR

K5Z

KRS

LCS

K62

KRR

LCR

K90

(ADG7)

K93

K8Z

K91

K92

K8Y

K90

K93

SAPH16F010300780

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Brand: Harmar Mobility Pages: 10
Oldsmobile 2004 Alero Owner'S Manual preview
2004 Alero
Brand: Oldsmobile Pages: 360
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Brand: Q'STRAINT Pages: 10
Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Brand: Farad Pages: 8
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Brand: iRacing Pages: 25
Veigel S47290920 Installation And Operating Instructions Manual preview
S47290920
Brand: Veigel Pages: 24
Cellular Line interphone Instruction Manual preview
interphone
Brand: Cellular Line Pages: 25
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Park-Daddy PD50AA Installation Manual preview
PD50AA
Brand: Park-Daddy Pages: 22
Chevrolet Malibu 2014 Owner'S Manual preview
Malibu 2014
Brand: Chevrolet Pages: 428
iOttie Aivo Connect Setup Manual preview
Aivo Connect
Brand: iOttie Pages: 58
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Brand: Skoda Pages: 16
Yakima K1249 Instructions Manual preview
K1249
Brand: Yakima Pages: 9
AIS MAZMOD2 Manual preview
MAZMOD2
Brand: AIS Pages: 2
THIEYE CarView 2 User Manual preview
CarView 2
Brand: THIEYE Pages: 88
Oldsmobile 2003 Silhouette Owner'S Manual preview
2003 Silhouette
Brand: Oldsmobile Pages: 466
Jeep Grand Cherokee SRT 2019 Owner'S Manual preview
Grand Cherokee SRT 2019
Brand: Jeep Pages: 656
Brink 4698 Fitting Instructions Manual preview
4698
Brand: Brink Pages: 26

Brands by name

Popular brands

Load more brands