Hino 238 Workshop Manual Download Page 273

Page: 273 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1050

•

Check that no DTC is detected after test drive.

8. Estimated failure factors

•

Sensor is disconnected or sensing unit is malfunctioning (due to dirt, clogging, damage, etc.)

•

Abnormal sensor resistance

•

Engine ECU sensor power supply failure or internal circuit failure

•

Harness disconnection or short-circuit

•

Looseness or poor contact of the connector

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Hino 238, Workshop Manual, Page: 273 / 919

Search results

Summary of Contents for 238

Reviews: