Hino 238 Page 738 Workshop Manual Download | Manualshive

Page: 738 / 919

background image

DEF SCR SYSTEM (DCU)

5–172

13

Inspect the
engine cool-
ant tempera-
ture sensor

1.

Check the installation of the
engine coolant temperature
sensor.

2.

Make sure there is no dirt or
damage to the engine cool-
ant temperature sensor.

Failure found:
Go to YES.

No failure
found: Go to
NO.

Clean the
engine cool-
ant tempera-
ture sensor
and install it
properly.
If damaged,
replace the
engine cool-
ant tempera-
ture sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 14.

14

Inspect the
engine cool-
ant tempera-
ture sensor
unit

Measure the resistance between
the terminals of the engine cool-
ant temperature sensor.
<Tester connections>
Engine coolant temperature sen-
sor
WTM+

–

WTM-

<Standard values>
20



C {68



F}: 2.59

–

2.32 k



80



C {176



F}: 0.326

–

0.310 k



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 15.

Replace the
engine cool-
ant tempera-
ture sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

15

Check the
DTC detected
(DCU)

Check if P205B has been
detected in [DCU].

DTC P205B
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Replace the
DCU.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Procedure
completed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

DTC: P205B

DEF tank temperature sensor - rationality

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
736
737
738
739
740
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

2005 Sierra Denali

Brand: GMC Pages: 428

Brand: Mercedes-Benz Pages: 346

Brand: Thule Pages: 4

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

Brand: REVCAMUK Pages: 4

Gasoline/Electric DS Golf Car 1996

Brand: Club Car Pages: 48

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

ULTIMATE SPEED 296713

Brand: walser Pages: 10

Brand: Mercedes-Benz Pages: 373

Brand: Anker Technology Pages: 8

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Mopar Pages: 18

Dodge Caravan 2002

Brand: Chrysler Pages: 2399

Brand: Ednet Pages: 6

Brand: LaserLine Pages: 4

Brand: Toyota Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands