manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–237

1.

Set the starter switch to the "LOCK" position.

2.

Disconnect the coolant cut off valve (DEF tank heater valve) con-
nector.

3.

Use the electrical tester to measure the resistance of the terminals
of the coolant cut off valve (DEF tank heater valve).

NO

YES

1.

Twenty seconds after the engine has started, grasp the pipe down-
stream of the coolant cut off valve (DEF tank heater valve) and
check if the pressure drops.

NO

YES

10

Inspect the coolant cut off valve (DEF tank heater valve) unit

LDU

LDV

SAPH16F020400159

Measurement 

conditions

Tester 

connections

Standard values

Starter switch: 
LOCK

Coolant cut off 
valve (DEF tank 
heater valve) con-
nector
LDU 

–

 LDV

20 

C {68 

F}:

9.04 

–

 9.52 

Do the measurements meet the standard value?

Go to step 11.

Replace the coolant cut off valve (DEF tank
heater valve).
Perform "After-inspection work" of INFOR-
MATION section.

11

Inspect the coolant cut off valve (DEF tank heater valve)

Did the pressure drop?

Go to step 12.

Replace the coolant cut off valve (DEF tank
heater valve).
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Porsche Carrera GT Manual preview
Carrera GT
Brand: Porsche Pages: 192
Mobile Create MCM3 Instruction Manual preview
MCM3
Brand: Mobile Create Pages: 15
Cadillac 2007 SRX Owner'S Manual preview
2007 SRX
Brand: Cadillac Pages: 522
Cadillac 2009 CTS Personalization Manual preview
2009 CTS
Brand: Cadillac Pages: 20
Actia SmarTach Manual preview
SmarTach
Brand: Actia Pages: 102
Menabo JUZA Fitting Instructions Manual preview
JUZA
Brand: Menabo Pages: 12
Icom RMK-5 Instruction Manual preview
RMK-5
Brand: Icom Pages: 20
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Brand: E&G Classics Pages: 2
Jaeger 12020523 Fitting Instructions Manual preview
12020523
Brand: Jaeger Pages: 11
Sagem MyCK100 User Manual preview
MyCK100
Brand: Sagem Pages: 10
TAUBENREUTHER 16-5911 Manual preview
16-5911
Brand: TAUBENREUTHER Pages: 18
Jeep Grand Cherokee SRT 2019 Owner'S Manual preview
Grand Cherokee SRT 2019
Brand: Jeep Pages: 656
Billien OBU 5050 Quick Installation Manual preview
OBU 5050
Brand: Billien Pages: 2
Lexus ES 2021 Quick Manual preview
ES 2021
Brand: Lexus Pages: 28
Voxx Electronics CA-510a Installation Instructions Manual preview
CA-510a
Brand: Voxx Electronics Pages: 15
Lippert Stargazer Spirit XTR Skylight Installation Manual preview
Stargazer Spirit XTR Skylight
Brand: Lippert Pages: 8
Toyota 2012 Sienna Owner'S Manual preview
2012 Sienna
Brand: Toyota Pages: 779
TATA Motors Harrier 2021 Owner'S Manual preview
Harrier 2021
Brand: TATA Motors Pages: 308

Brands by name

Popular brands

Load more brands