Hino 238 Workshop Manual Download Page 849

Page: 849 / 919

DEF SCR SYSTEM (DCU)

5–283

INSPECTION PROCEDURE: P2201

Set the starter switch to the "LOCK" position.

Connect the vehicle to Hino-DX.

Set the starter switch to the "ON" position.

Select [DCU] and check if any DTC other than P2201 (for example
P2202, P2209, U029D) has been detected in [Fault Information].

YES

Check the DTC detected (DCU) [Hino-DX]

Select

DCU

SAPH16F020400191

Has a DTC other than P2201 been detected?

Go to diagnosis procedure of a related DTC.

Go to step 2.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands