manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1300

INSPECTION PROCEDURE: P268A and P2696

1.

Check injector replaced record.

NO

YES

1.

Re-input the registration injector calibration data (QR CODE) of
the service server.

2.

Erase the DTC memory, and check again DTC code. Check that
(P268A or P2696) has not been displayed in [Fault Information].

NO

YES

1

Check the injector replace record

Does the injector have a replacement record?

Go to step 3.

Go to step 2.

2

Inspect the injector calibration data (QR CODE) [Hino-DX]

Select

Engine

SAPH16F010301025

Has DTC (P268A or P2696) been detected?

Go to step 3.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

HUSKY LINERS X-ACT CONTOUR 53491 Care And Use Instructions preview
X-ACT CONTOUR 53491
Brand: HUSKY LINERS Pages: 2
Volvo 30728293 Installation Instructions Manual preview
30728293
Brand: Volvo Pages: 19
Waeco MagicComfort MSH200 Installation And Operating Instructions Manual preview
MagicComfort MSH200
Brand: Waeco Pages: 108
Tusk RL-HM018R Installation Instructions And Information Manual preview
RL-HM018R
Brand: Tusk Pages: 2
Saab 2008 9-5 Owner'S Manual preview
2008 9-5
Brand: Saab Pages: 288
Sunsky S-GPS-0142 User Manual preview
S-GPS-0142
Brand: Sunsky Pages: 9
Kia 2014 rondo Features preview
2014 rondo
Brand: Kia Pages: 11
Saab 2008 9-7x Owner'S Manual preview
2008 9-7x
Brand: Saab Pages: 426
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Brand: Carcomm Pages: 2
Mazda 2008 B2300 Truck Owner'S Manual preview
2008 B2300 Truck
Brand: Mazda Pages: 280
Needit Park Mini User Manual preview
Park Mini
Brand: Needit Pages: 2
Gemini KIT ParkingSensor 814 Installation And Use Manual preview
KIT ParkingSensor 814
Brand: Gemini Pages: 6
Dometic LMC Eriba Nova Service Manual preview
LMC Eriba Nova
Brand: Dometic Pages: 24
Ford F-250 Super Duty 2022 Owner'S Manual preview
F-250 Super Duty 2022
Brand: Ford Pages: 740
Gentex ADVGEN20A Manual preview
ADVGEN20A
Brand: Gentex Pages: 2
K&N Engineering Filtercharger 57-9004 Installation Manual preview
Filtercharger 57-9004
Brand: K&N Engineering Pages: 4
Honda Element 2004 Owner'S Manual preview
Element 2004
Brand: Honda Pages: 219
Mid America Motorworks 602-781 Instruction Sheet preview
602-781
Brand: Mid America Motorworks Pages: 2

Brands by name

Popular brands

Load more brands