Hino 238 Workshop Manual Download Page 187

Page: 187 / 919

ENGINE CONTROL SYSTEM (J08E)

4–964

INSPECTION PROCEDURE: P2101

Check the air cleaner element for dirt or damage, and make sure
the replacement period has not expired.

YES

Check that the air hose and pipe have no disconnections, clog-
ging, ruptures, or cracks.

Inspect the air cleaner element

Check indicator

Check for dirt, clogging,

and original parts

SAPH16F010300745

Was any failure found?

Clean or replace the air cleaner element.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

Inspect the air hose and air pipe

Check tightness and no bending

Check tightness, no bending and
no leak

SAPH16F010300746

Was any failure found?

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands