Hino 238 Page 695 Workshop Manual Download

Page: 695 / 919

DEF SCR SYSTEM (DCU)

5–129

DTC: P2048

EN01H16F02040F03001030

DTC: P2048 DEF injector - disconnection (Disconnection (low side))

INFORMATION

1. Technical description

•

DEF dosing valve is controlled by DCU.

•

DEF dosing valve detects disconnection and short-circuit based on the circuit voltage and signals in DCU.

<Description of malfunction>

•

DEF injector failure is detected.

2. DTC set condition

(1) DTC detection condition

Starter switch ON.
DEF injector duty cycle

(2) Judgement criteria

DEF dosing valve circuit voltage (Low side): Below 0.2 V for more than 0.05 sec.

3. Reset condition

•

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

DEF injection is stopped.

•

NOx purification function is stopped.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Exhaust gas purification function is declined.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

8. Estimated failure factors

•

Disconnection or short-circuit in sensor harness

•

Abnormal resistance of DEF injector

•

Malfunction in DEF injector

LG6

(DMH)

LG7

LF8

(DML)

(DMH)

(DML)

LF9

Twist

DCU

Dosing

module

(DEF

injector)

SAPH16F020400083

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands