manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1010

INSPECTION PROCEDURE: P2138

1.

Connect the vehicle to Hino-DX.

2.

Set the starter switch to the "ON" position.

3.

Select [Engine] and check if any DTC other than P2138 (for exam-
ple, P2122, P2123, P2127, P2128) has been detected in [Fault
Information].

NO

YES

1.

Check that the GND circuit of the PTO accelerator sensor is con-
nected to the appropriate harness.

NO

YES

1.

Check the connection of the accelerator sensor connector (Loose-
ness and poor contact).

NO

YES

1

Check the DTC detected (Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300781

Has a DTC other than P2138 been detected?

Go to the diagnostic procedure of a related
DTC.

Go to step 2.

2

Inspect the PTO accelerator sensor

Was any failure found?

Repair the GND circuit of the PTO accelerator
sensor.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 3.

3

Inspect the accelerator sensor connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 4.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Brand: GMC Pages: 140
A-Tach Mounts 50131 Instructions preview
50131
Brand: A-Tach Mounts Pages: 2
Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Brand: Bimmer Jakes Pages: 4
SAF-HOLLAND FleetMaster Air FW8 Series Owner'S Manual preview
FleetMaster Air FW8 Series
Brand: SAF-HOLLAND Pages: 20
Rightline Gear Car Top Duffle Bag Setup Manual preview
Car Top Duffle Bag
Brand: Rightline Gear Pages: 2
Dacia 2014 Sandero Driver'S Handbook Manual preview
2014 Sandero
Brand: Dacia Pages: 238
Cadillac Escalade ESV 2014 Owner'S Manual preview
Escalade ESV 2014
Brand: Cadillac Pages: 508
Hama Liberty III Quick Start Manual preview
Liberty III
Brand: Hama Pages: 2
Hyundai Santa Fe 2006 Owner'S Manual preview
Santa Fe 2006
Brand: Hyundai Pages: 280
Skoda Fabia II 2007 Workshop Manual preview
Fabia II 2007
Brand: Skoda Pages: 165
aci ADARAC Aluminum M Series Installation Instructions Manual preview
ADARAC Aluminum M Series
Brand: aci Pages: 16
Imiola HAK-POL O/018 Quick Manual preview
O/018
Brand: Imiola HAK-POL Pages: 3
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12
Skoda Superb 2006 Owner'S Manual preview
Superb 2006
Brand: Skoda Pages: 281
ConWys AG 21500598C VW Fitting Instructions Manual preview
21500598C VW
Brand: ConWys AG Pages: 16
ICON 91824E Installation Instructions preview
91824E
Brand: ICON Pages: 4
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Brand: Mynew Pages: 5

Brands by name

Popular brands

Load more brands