Hino 238 Workshop Manual Download Page 853

Page: 853 / 919

DEF SCR SYSTEM (DCU)

5–287

Check the installation of the air flow sensor.

Make sure there is no dirt or damage to the air flow sensor.

YES

Inspect the air flow sensor

Air flow sensor

SAPH16F020400196

Was any failure found?

If dirt, clogging or damage in the sensing
unit was found, replace the air flow sensor.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 6.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands