Hino 238 Page 524 Workshop Manual Download

Page: 524 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1301

Read the injector calibration data (QR CODE) of the injectors
using Hino-DX, re-input injector calibration data (QR CODE).

Erase the DTC memory, and check again DTC code. Check that
(P268A or P2696) has not been displayed in [Fault Information].

YES

Inspect the injector calibration data (QR CODE) [Hino-DX]

SAPH16F010301026

Has DTC (P268A or P2696) been detected?

Replace the engine ECU.
Perform "After-inspection work" of INFOR-
MATION section.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands