Hino 238 Page 442 Workshop Manual Download | Manualshive

Page: 442 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1219

CHECKLIST: P2463

DTC: P2463

DPF clogged

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Check the
DTC detected
(Engine ECU)
[Hino-DX]

Check if any DTC other than
P2463 has been detected in
[Engine].

DTC other
than P2463
have been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Go to diagno-
sis procedure
of a related
DTC.

Go to step 2.

2

Check the
DTC detected
(Burner)

Check if DTC has been detected
in [Burner].

DTC has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Go to diagno-
sis procedure
of a related
DTC.

Go to step 3.

3

Burner sys-
tem check 1
[Hino-DX]

1.

Collect the burner events log
from the Hino-DX.

2.

Check whether [EECU
REQUEST START AUTO
REGEN] is the latest.

3.

Check [FAILED IGNITION
(MISFIRE)] ,[LOST FLAME]
or [CANNOT ACHIEVE
TEMP] are displayed after
the latest [EECU REQUEST
START AUTO REGEN].

Correspond-
ing log: Go to
YES.

No corre-
sponding log:
Go to NO.

If [FAILED
IGNITION
(MISFIRE)] is
displayed, go
to DTC P140D
inspection pro-
cedure.
If [LOST
FLAME] is dis-
played, go to
DTC P140E
inspection pro-
cedure.
If [CANNOT
ACHIEVE
TEMP] is dis-
played, go to
DTC P1400
inspection pro-
cedure.

Go to step 4.

4

Burner sys-
tem check 2
[Hino-DX]

1.

From the retrieved log,
check if [EECU REQUEST
START MANUAL REGEN] is
displayed after the newest
(latest) [EECU REQUEST
START AUTO REGEN].

Correspond-
ing log: Go to
YES.

No corre-
sponding log:
Go to NO.

Go to step 5.

Go to step 7.

«
...
440
441
442
443
444
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: KC HiLiTES Pages: 4

Brand: Happy Orange Pages: 2

Brand: Toyota Pages: 529

Brand: Laser Pages: 8

Brand: Wallbox Pages: 7

Brand: Warrior Products Pages: 3

10-8002-C11670C

Brand: Saleen Pages: 17

Brand: Renault Pages: 340

Evo All THAR-FOR3

Brand: Fortin Pages: 7

Brand: Simplicity Pages: 10

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brand: JBL Pages: 12

Brand: Whispbar Pages: 63

Brand: GYS Pages: 32

MagicSafe MSG150

Brand: Waeco Pages: 20

Brand: CSL Pages: 8

Brand: Kuda Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands