Hino 238 Workshop Manual Download Page 29 | Manualshive

Page: 29 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–806

CHECKLIST: P1133

DTC: P1133

PTO accelerator sensor (Hi)

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Inspect the
PTO accelera-
tor sensor con-
nector

Check the connection of the PTO
accelerator sensor connector
(Looseness and poor contact).

Failure found:
Go to YES.

No failure
found: Go to
NO.

Connect
securely,
repair if
needed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 2.

2

Inspect the
PTO accelera-
tor sensor

1.

Check the installation of the
PTO accelerator sensor.

2.

Make sure there is no dirt or
damage to the PTO acceler-
ator sensor.

Failure found:
Go to YES.

No failure
found: Go to
NO.

Clean the PTO
accelerator
sensor and
install it prop-
erly.
If damaged,
replace the
sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 3.

3

Inspect the
PTO accelera-
tor sensor unit

Disconnect the PTO accelerator
sensor connector and measure
the resistance between the termi-
nals of the PTO accelerator sen-
sor.
<Tester connections>
PTO accelerator sensor
SIG

–

VCC

SIG

–

GND

<Standard values>
More than 2



The measure-
ments meet
the standard
value: Go to
YES.

Go to step 4.

Replace the
sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

4

Inspect for
short-circuit of
the PTO accel-
erator sensor
harness

Connect the signal check harness
to the engine ECU. (Do not con-
nect harness to the ECU.)
Measure the resistance between
the terminals of the engine ECU
(signal check harness) and
ground.
<Tester connections>
Engine ECU (signal check har-
ness)
ASCS(V68)

–

Ground

AVC5(V71)

–

Ground

<Standard values>





The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 5.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

«
...
27
28
29
30
31
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: Jeep Pages: 608

Brand: Fab Fours Pages: 21

Brand: mtf TRANSPORT SYSTEM Pages: 9

Brand: GMC Pages: 430

Brand: Guidosimplex Pages: 8

Akerstroms Tx700

Brand: LXE Pages: 146

MagicSafe MSG150

Brand: Waeco Pages: 20

1953 Traction Avant

Brand: CITROEN Pages: 26

Brand: Mitsubishi Pages: 490

transit connect 2012

Brand: Ford Pages: 299

Brand: Roadefend Pages: 15

Brand: Kia Pages: 673

Brand: Alpine Pages: 70

Brand: Ford Pages: 10

Brand: Fiat Pages: 204

Brand: Aries Pages: 6

Brand: Falcon Pages: 36

Brand: Comtronics Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands