Hino 238 Page 409 Workshop Manual Download | Manualshive

Page: 409 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1186

7

Check burner
system 4
[Hino-DX]

In the obtained log, check if
[FAILED IGNITION (MISFIRE)],
[LOST FLAME], [CANNOT
ACHIEVE TEMP] are present
after [EECU REQUEST START
MANUAL REGEN].

Correspond-
ing log: Go to
YES.

No corre-
sponding log:
Go to NO.

If [FAILED
IGNITION
(MISFIRE)] is
displayed, go
to DTC P140D
inspection pro-
cedure.
If [LOST
FLAME] is dis-
played, go to
DTC P140E
inspection pro-
cedure.
If [CANNOT
ACHIEVE
TEMP] is dis-
played, go to
DTC P1400
inspection pro-
cedure.

This is due to
the fact that
during the
DPR manual
regeneration
stepping on
the accelerator
pedal, moving
the shift, work-
ing on the PTO
and pressing
two time the
DPR button
will cancel the
manual regen-
eration.
-Replace the
DPR filter and
the burner
nozzle, and
clean the
igniter.
-After perform-
ing the DPR
manual regen-
eration, the
inspection pro-
cedure will be
complete.
Perform "After-
inspection
work" of
INFORMA-
TION section.

8

Inspect DPR
switch

1.

Check the connection of the
DPR switch connector.
(Looseness and poor con-
tact)

2.

Check the switch unit.

3.

Inspect the harness for dis-
connections and short-cir-
cuits.

Failure found:
Go to YES.

No failure
found: Go to
NO.

-Repair or
replace the
faulty part.
-Replace the
DPR filter and
the burner
nozzle and
clean the
igniter.
-After DPR
manual regen-
eration, the
diagnosis pro-
cedure will be
complete.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 9.

DTC: P244B

Incomplete regeneration (check sheet 2)

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
407
408
409
410
411
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: ULTIMATE SPEED Pages: 19

Brand: Warrior Products Pages: 4

Brand: Mobile Create Pages: 15

Brand: FAAFTECH Pages: 8

Brand: AutoMaxi Pages: 2

Brand: PEUGEOT Pages: 249

Brand: VER-MAC Pages: 64

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: SAN HIMA Pages: 10

Brand: Yakima Pages: 12

Brand: FALCON RIDGE Pages: 6

1995 Roadmaster

Brand: Buick Pages: 340

Brand: VP Autoparts Pages: 2

Brand: Hyundai Pages: 32

Brand: Prime Design Pages: 16

Brand: Saab Pages: 9

Brand: GMC Pages: 364

Brand: Honda Pages: 434

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands