manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1012

1.

Set the starter switch to the "LOCK" position.

2.

Disconnect the accelerator sensor connector.

3.

Set the starter switch to the "ON" position.

4.

Use the electrical tester to measure the voltage between the termi-
nals of the engine ECU (signal check harness) and ground.

NO

YES

5

Inspect the engine ECU

B

V67

V47

SAPH16F010300783

Measurement

conditions

Tester connections

Standard values

Starter switch: 
ON

Engine ECU (signal 
check harness)
ACS1(V47) 

–

 Ground

ACS2(V67) 

–

 Ground

0 V

Do the measurements meet the standard value?

Procedure completed.
Clear and check again the DTC.
Perform "After-inspection work" of INFOR-
MATION section.

Replace the engine ECU.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

LAMBORGHINI URUS Quick Manual preview
URUS
Brand: LAMBORGHINI Pages: 48
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Brand: Waeco Pages: 212
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Brand: minnid Pages: 44
Honda 2010 Civic Sedan Owner'S Manual preview
2010 Civic Sedan
Brand: Honda Pages: 390
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Brand: Cadillac Pages: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Brand: Fortin Pages: 9
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Brand: Cadillac Pages: 19
Charge Amps Halo Pole Mount Manual preview
Halo Pole Mount
Brand: Charge Amps Pages: 14
Toyota 1998 Celica Owner'S Manual preview
1998 Celica
Brand: Toyota Pages: 204
Jotto Desk Force 475-0750 Installation Instructions preview
Force 475-0750
Brand: Jotto Desk Pages: 3
Toyota 2009 Highlander Quick Reference Manual preview
2009 Highlander
Brand: Toyota Pages: 19
Black & Decker PIUSB2B Instruction Manual preview
PIUSB2B
Brand: Black & Decker Pages: 24
Toyota RAV4 2019 Owner'S Manual preview
RAV4 2019
Brand: Toyota Pages: 244
Blueant SUPERTOOTH 3 User Manual preview
SUPERTOOTH 3
Brand: Blueant Pages: 48
Honda 2011 Pilot Owner'S Manual preview
2011 Pilot
Brand: Honda Pages: 574
ETC CarPlay NV17 Manual preview
CarPlay NV17
Brand: ETC Pages: 11
Sune Technology SUNE10 VELAR Installation Manual preview
SUNE10 VELAR
Brand: Sune Technology Pages: 8
JVC KV-K1017 Installation & Connection Manual preview
KV-K1017
Brand: JVC Pages: 12

Brands by name

Popular brands

Load more brands