manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1304

•

Battery voltage 

>

 11 V

•

DEF tank sensor is working normally.

•

There is no interruption between DEF tank sensor and CAN.

[After malfunction is detected]

•

DEF has been refilled with the starter switch ON.

(2) Judgement criteria

•

The average value of DEF concentration over 10 seconds is below the standard value.

3. Reset condition

•

After restoration to normal condition.

4. Indication, warning or system control regulation when the DTC is set.

•

Diag lamp: ON (DEF quality malfunction lamp)

•

Engine output is restricted.

•

Vehicle speed is restricted.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient.

•

Vehicle does not speed up.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is detected after test drive.

8. Estimated failure factors

•

Abnormal DEF concentration

•

Dirt or foreign substance inside DEF tank

•

DEF quality sensor failure

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Camcar 40000 Manual preview
40000
Brand: Camcar Pages: 6
Ignition 63-231 Quick Start preview
63-231
Brand: Ignition Pages: 1
Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Brand: Jeep Pages: 608
Jeep PATRIOT 2013 Specifications preview
PATRIOT 2013
Brand: Jeep Pages: 5
Jeep PATRIOT 2012 Specifications preview
PATRIOT 2012
Brand: Jeep Pages: 6
Jeep Grand Cherokee SRT 2014 Operating Manual preview
Grand Cherokee SRT 2014
Brand: Jeep Pages: 345
Jeep Grand Cherokee 2015 User Manual preview
Grand Cherokee 2015
Brand: Jeep Pages: 236
Jeep Grand Cherokee Quick Manual To Repairs preview
Grand Cherokee
Brand: Jeep Pages: 18
Jeep Grand Cherokee Quick Reference Manual preview
Grand Cherokee
Brand: Jeep Pages: 24
Jeep Compass 2015 Owner'S Manual preview
Compass 2015
Brand: Jeep Pages: 560
Jeep Compass 2013 Owner'S Manual preview
Compass 2013
Brand: Jeep Pages: 525
Jeep Cherokee 2019 User Manual preview
Cherokee 2019
Brand: Jeep Pages: 308
Jeep CHEROKEE 2017 Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 86
Jeep CHEROKEE 2017 Owner'S Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 638
Jeep 2022 CHEROKEE Quick Start Manual preview
2022 CHEROKEE
Brand: Jeep Pages: 9
Jeep 2014 Patriot Service Information preview
2014 Patriot
Brand: Jeep Pages: 51
Jeep Jeep Wrangler Buyer'S Manual preview
Jeep Wrangler
Brand: Jeep Pages: 4
Jeep Jeep Wrangler Owner'S Manual Supplement preview
Jeep Wrangler
Brand: Jeep Pages: 50

Brands by name

Popular brands

Load more brands