background image

The Trusted Source

®

Full Width 

Full Width Bumper

Narrow Bumper

Narrow Bumper

TO REDUCE RISK OF SERIOUS INJURY OR PROPERTY DAMAGE:
READ ALL SAFETY MESSAGES AND UNDERSTAND ALL 
INSTRUCTIONS AND PROCEDURE 

NOTICES

BEFORE 

ATTEMPTING TO INSTALL OR USE THIS PRODUCT.

MOUNT WINCH USING ONLY APPROVED MOUNTING PLATE.
BUMPER/WINCH PLATE NOT INTENDED FOR WINCHES IN EX-
CESS OF 10000LBS. LOAD LIMITS FOR YOUR BUMPER/WINCH
MAY BE LESS DEPENDING ON CONDITION OF YOUR VEHICLE
AND ATTACHMENTS. FOLLOW ALL INSTRUCTIONS, LIMITATIONS
& WARNINGS WITH YOUR VEHICLE, THIS PRODUCT, YOUR
WINCH AND SAFE WINCHING PRACTICES SUPPLEMENT. 

RISK OF EYE INJURY! SAFETY GLASSES MUST BE WORN AT
ALL TIMES WHILE INSTALLING OR MAINTAINING THIS PRODUCT. 
TORQUE AND RECHECK FASTENERS AFTER 250 MILES AND
FREQUENTLY THEREAFTER. INSPECT BUMPER, WINCH AND
MOUNT BEFORE USE. DO NOT USE IF DAMAGED. 

CHECK STATE AND LOCAL HIGHWAY SAFETY LAWS REGARDING
PERMITTED BUMPER TYPES AND HEIGHTS. 

Quadratec

®

Aluminum

Front Bumpers

Installation Manual for ’07-’18 Wrangler JK Vehicles

#

12057.0263 and 12057.0264

Q_JK_ALUM_FBMPR_12057_9261_A4.qxp_A4  12/10/19  2:36 PM  Page 1

Summary of Contents for 12057.0263













Reviews: