background image

Page 1 of 8 

 

292-2769  

 

8/12/08 

Please read BOTH these Installation Instructions and the General 

Instructions before attempting to install or operate this equipment.

1.   Blue Ox

®

 towing products and accessories 

      are intended to be installed by Blue Ox

® 

      Dealers who are familiar with our products and
      have the equipment necessary and knowledge
      to do “fi t work”. When necessary Blue Ox

®

 

      Dealers can be found at 

www.blueox.us 

or by 

      contacting our 24/7 Customer Care 
      Department at (402) 385-3051.

2.   Many Blue Ox

®

 Baseplates are designed to 

      use existing holes and hardware to mount 
      the baseplate to the towed vehicle. Even
      though bolts are there, do not assume they 
      are adequate for baseplate mounting. Always
      use hardware supplied in the hardware kit 
      and existing hardware specifi ed in the 
      Baseplate Installation Instructions. 

Confi rm the towability and pre-towing 

procedures for your vehicle with 

the owner’s manual or contact the 
vehicle’s manufacturer for specifi c 

towing procedures. You can also 

contact REMCO for additional 

information at 1(800)228-2481.

Attachment Tab Height: 

14.5”

Attachment Tab Width: 

22”

2005 Kia Spectra

Installation Instructions

BX2711

Bolt Size

Grade 5

Grade 8

1/4”

10

14

5/16”

19

29

3/8”

33

47

7/16”

54

78

1/2”

78

119

5/8”

154

230

Bolt Torque Specifi cations 

Torque in Foot-Pounds per Inch Bolts

 

Bolt Torque Specifi cations 

Torque in Foot-Pounds per Metric Bolts 

Bolt Size Grade 8.8 Grade 10.9

6MM

6

8

8MM

16

22

10MM

31

40

12MM

54

70

14MM

89

117

Serial Number

!

Failure to read and follow these instructions 

could result in separation of the towed vehicle 

from the tow bar, causing property damage, 

loss of towed vehicle, personal injury or death.

WARNING

Summary of Contents for BX2711









Reviews: