background image

INPUT VOLTAGE  ........................10 to 30 Volts DC.

INPUT CURRENT  .......................0.5A @ 12.8V, 0.45A @ 25.6V

LIGHT OUTPUT ...........................AMBER: 160+ LUMENS

 

BLUE: 155+ LUMENS

 

RED: 123+ LUMENS

 

WHITE: 660+ LUMENS

CABLE LENGTH ..........................7 FT. (HEAD A), 4FT. (HEAD B)

LED ELEMENTS ..........................4 (EACH HEAD)

FLASH PATTERNS ......................16 (8 Standard, 8 optional cycle)

MAX NUMBER OF SYNC’D HEADS ... 64

WARRANTY PERIOD ..................5 YEARS

TECHNICAL SPECIFICATIONS

DIMENSIONS

INSTALLATION GUIDE

MOUNTING

Drill a 1” diameter hole in the reflector of the lens assembly.

A 1” hole saw is typically used. The HIDE-A-LED™ may be used as a 

template to mark the location of the two screw holes. The W600 may 

be mounted in either the back surface, bottom or sides of a reflector.  

Drill pilot holes with a 7/64” drill bit. Install the HIDE-A-LED™ into the 

lens assembly using the supplied gasket and screws. If the mount-

ing surface is curved additional sealing may be necessary. Use RTV 

Silicone sealant if needed.

ELECTRICAL CONNECTIONS

The wiring diagram on page 2 shows a typical install.

RED: 

+V

Connect to +V through an ON/OFF switch.

The use of a fuse located close to the voltage source is recommended. 

Size the fuse according to the number of heads used in the system. 

18AWG or larger wire is recommended.

BLACK:

 - GROUND

Connect to - GROUND 

vehicle chassis.

18AWG or larger wire is recommended.

BLUE:

 Flash pattern SYNC and SELECTION wire.

If you wish to have all the LED heads synchronize 

their flash timings and patterns with each other then all the BLUE wires 

must be connected together(64 Heads Maximum).

The BLUE wire is also used to select the flash pattern.

Touch the BLUE wire to +V to select the next pattern in the FLASH 

PATTERN LIST. The BLUE wire can also be run to a momentary 

push-button located on the dashboard to allow the flash pattern to be 

changed when desired.

Note: Do not connect the BLUE wire to - Ground.

It will disrupt the flash pattern sync signal.

PAGE 1

920-9121-00 REV. C

DEUCE

LED HEAD

POWER MODULE

833 W. Diamond St Boise, Idaho 83705

TEL: 888-844-6682  www.strobe.com

THE HEATSINK WILL BE HOT AFTER RUNNING

FOR AN EXTENDED PERIOD. 

DO NOT TOUCH.

IT 

WILL NOT

 MELT ANY OF THE PLASTIC 

PARTS OF THE LENS ASSEMBLY.

STRAP THE WATERPROOF

POWER MODULE TO THE BODY

OF THE VEHICLE 

AWAY FROM

ANY HIGH HEAT SOURCES.

! HOT !

GASKET

REFLECTOR

DO NOT DRILL HOLES THROUGH THE POWER MODULE!

1” HOLE

7/64” PILOT 

HOLES

SCREWS

TIP: APPLY RTV SILICONE

TO THE SCREWS TO SEAL

THE THREADS.

LOCATE LED HEAD AT LEAST 1” AWAY 

FROM ANY FACTORY BULB!

FOR DUAL WALL REFLECTORS: FIRST USE A 1.5” HOLE SAW TO DRILL THROUGH OUTER 

LAYER ONLY.  THEN USE 1” HOLE SAW TO DRILL THROUGH INNER LAYER USING SAME 

PILOT DRILL HOLE. INSTALL THE LED HEAD THROUGH THE 1.5” HOLE AND SEAL THE GAP 

WITH RTV SILICONE.

DUAL HEAD W600

1

SYNC

TM

1.50"

0.875"

1.28"

0.150"

0.980"

1.50"

4.89"

"5

9.

0

0.59"

HEAD A

HEAD B

INPUT MABLE: 4FT

LED HEAD

CABLES:

4FT, 7FT

CONNECTOR SEALING

Reviews: