Hino 238 Workshop Manual Download Page 785

Page: 785 / 919

DEF SCR SYSTEM (DCU)

5–219

DTC: P20A3

EN01H16F02040F03001046

DTC: P20A3 Reverting valve for DEF pump - circuit (Circuit high)

INFORMATION

1. Technical description

•

DCU detects the circuit failure based on the circuit voltage of the DEF pump reverting valve.

<Description of malfunction>

•

Failure of reverting valve in DEF pump is detected.

2. DTC set condition

(1) DTC detection condition

Starter switch ON.
DEF reverting valve is activated.

(2) Judgement criteria

DEF reverting valve voltage:

≤

2.7 V for 2 sec.

3. Reset condition

•

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

DEF injector and DEF pipe may rupture when DEF freezes.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

–

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

8. Estimated failure factors

•

Disconnection or short-circuit in sensor harness

•

Irregular contact (disconnection or poor fit of connector)

•

Malfunction of DEF reverting valve

Supply module

(DEF pump)

DCU

LFQ

(PSR+)

LFR

LGD

(PSRS)

(PSR+)

(PSRS)

LFP

LGF

(PSR-)

LFJ

(PMP+)

LFL

LG8

(PMPS)

(PMP+)

(PMPS)

LFK

LGA

(PMP-)

LFM

LGB

(PMV+)

LFN

LGC

(PMV-)

LGE

LG9

SAPH16F020400144

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands