Hino 238 Workshop Manual Download Page 701

Page: 701 / 919

DEF SCR SYSTEM (DCU)

5–135

DTC: P2049

EN01H16F02040F03001031

DTC: P2049 DEF injector - disconnection (Disconnection (high side))

INFORMATION

1. Technical description

•

DEF dosing valve is controlled by DCU.

•

DEF dosing valve detects disconnection and short-circuit based on the circuit voltage and signals in DCU.

<Description of malfunction>

•

DEF injector failure is detected.

2. DTC set condition

(1) DTC detection condition

Starter switch ON.
DEF injector duty cycle

0 %

(2) Judgement criteria

DEF dosing valve circuit voltage (High side): Below 2 V for more than 0.05 sec.

3. Reset condition

•

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

SCR system malfunction lamp: ON

•

DEF injection is stopped.

•

NOx purification function is stopped.

•

If malfunction does not improve within 500 miles: engine output is restricted.

•

If malfunction does not improve within 2,000 miles: vehicle speed is restricted.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Exhaust gas purification function is declined.

•

Engine output is insufficient (when malfunction does not improve within 500 miles).

•

Vehicle does not speed up (when malfunction does not improve within 2,000 miles).

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

LG6

(DMH)

LG7

LF8

(DML)

(DMH)

(DML)

LF9

Twist

DCU

Dosing

module

(DEF

injector)

SAPH16F020400088

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands