Renesas SH7763 Hardware Manual Download Page 701 | Manualshive

Page: 701 / 2026

background image

Section 16 Clock Pulse Generator (CPG)

Rev. 1.00 Oct. 01, 2007 Page 635 of 1956

REJ09B0256-0100

The functions of the blocks in the CPG are as follows.

(1) PLL

Circuit

1

PLL circuit 1 multiples the frequency of the crystal oscillator or the clock input from the EXTAL
pin by the ratio of

×

16. The multiplication ratio is selected by the combination of mode control

pins MD0, MD1, and MD2.

(2) PLL

Circuit

2

PLL circuit 2 aligns the phases of the bus clock (Bck) and the clock signal output from the
CLKOUT pin that is used by the external peripheral interface.

(3) Crystal

Oscillator

The crystal oscillator is a clock pulse generator used when a crystal resonator is connected to the
XTAL or EXTAL pin. The crystal oscillator can be enabled by the MD8 pin setting.

(4) Divider

1

Divider 1 generates the CPU clock (Ick), SHwy clock (SHck), peripheral module clocks (Pck0,
Pck1), and bus clock (Bck). The division ratio is selected by the combination of mode control pins
MD0, MD1, and MD2.

(5) Frequency Control Register (FRQCR)

The frequency control register is a read-only register that depends on the combination of mode
control pins MD0, MD1, and MD2.

(6) PLL

Circuit

3

PLL circuit 3 multiples the frequency of the SHwy clock (SHck) by the ratio of

×

4.

(7) Divider

2

Divider 2 generates the DDR-memory clocks (DDRck0, DDRck90, DDRck180, and DDRck270).

(8) PLL Control Register (PLLCR)

The PLL control register has control bits assigned for enabling or disabling the CLKOUT pin
output.

«
...
699
700
701
702
703
...
»

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Brand: dbx Pages: 2

Brand: dbx Pages: 17

Brand: Jetter Pages: 35

xCORE-200 Multi-channel Audio board

Brand: XMOS Pages: 112

Brand: Accom Pages: 15

Brand: Hama Pages: 6

Brand: Marani Pages: 39

Brand: Hauppauge Pages: 62

Brand: ICOP Technology Pages: 34

Brand: ZiLOG Pages: 317

cPCIS-1100 Series

Brand: ADLINK Technology Pages: 48

Brand: Cypress Semiconductor Pages: 28

Brand: Digisol Pages: 73

Brand: Roland Pages: 224

NVR52A16-16P-4KS2

Brand: Dahua Technology Pages: 13

Wireless G F5D7000

Brand: Belkin Pages: 252

Brand: IC Realtime Pages: 131

Instruction Card Video DC Block

Brand: Extron electronics Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands