Renesas SH7763 Hardware Manual Download Page 1521 | Manualshive

Page: 1521 / 2026

background image

Section 34 Serial Sound Interface (SSI)

Rev. 1.00 Oct. 01, 2007 Page 1455 of 1956

REJ09B0256-0100

When an underflow or overflow error condition is met, the CHNO[1:0] and SWNO bits can be
used to recover the SSI module to a known status. When an underflow or overflow occurs, the
host CPU can read the number of channels and the number of system words to determine what
point the serial audio stream has reached. In the transmitter case, the host CPU can skip forward
through the data it wants to transmit until it finds the sample data that matches what the SSI
module is expecting to transmit next, and so resynchronize with the audio data stream. In the
receiver case, the host CPU can skip forward storing null sample data until it is ready to store the
sample data that the SSI module is indicating that it will receive next to ensure consistency of the
number of received data, and so resynchronize with the audio data stream.

34.4.6 Serial

Clock

Control

This function is used to control and select which clock is used for the serial bus interface.

If the serial clock direction is set to input (SCKD = 0), the SSI module is in clock slave mode, then
the bit clock that is used in the shift register is derived from the SSI_SCK pin.

If the serial clock direction is set to output (SCKD = 1), the SSI Module is in clock master mode,
and the shift register uses the bit clock derived from the SSI_CLK input pin or its clock divided.
This input clock is then divided by the ratio in the serial oversampling clock division ratio
(CKDV) bit in SSICR and used as the bit clock in the shift register.

In either case, the SSI_SCK pin output is the same as the bit clock.

«
...
1519
1520
1521
1522
1523
...
»

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Brand: Paradyne Pages: 20

Compshere 3000 Series

Brand: Paradyne Pages: 2

Brand: Softing Pages: 4

Brand: Teletronics International Pages: 57

Brand: EMTRUST Pages: 103

Brand: Network Critical Pages: 200

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

HFisolator 9730/26-11

Brand: Stahl Pages: 2

Brand: Smacq Technologies Pages: 22

Brand: Digisol Pages: 73

Brand: ekwb Pages: 10

Brand: Mod Pages: 11

Brand: LanReady Pages: 40

Brand: ZALMAN Pages: 12

Brand: Patton electronics Pages: 93

Brand: Intel Pages: 57

Brand: Renesas Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands