Renesas SH7763 Hardware Manual Download Page 118 | Manualshive

Page: 118 / 2026

background image

Section 2 Programming Model

Rev. 1.00 Oct. 01, 2007 Page 52 of 1956

REJ09B0256-0100

2.4

Data Formats in Registers

Register operands are always longwords (32 bits). When a memory operand is only a byte (8 bits)
or a word (16 bits), it is sign-extended into a longword when loaded into a register.

31

S

S

S

0

6

7

6

7

0

31

S

S

S

0

14

15

14

15

0

Figure 2.6 Formats of Byte Data and Word Data in Register

2.5

Data Formats in Memory

Memory data formats are classified into bytes, words, and longwords. Memory can be accessed in
an 8-bit byte, 16-bit word, or 32-bit longword form. A memory operand less than 32 bits in length
is sign-extended before being loaded into a register.

A word operand must be accessed starting from a word boundary (even address of a 2-byte unit:
address 2n), and a longword operand starting from a longword boundary (even address of a 4-byte
unit: address 4n). An address error will result if this rule is not observed. A byte operand can be
accessed from any address.

Big endian or little endian byte order can be selected for the data format. The endian should be set
with the external pin after a power-on reset. The endian cannot be changed dynamically. Bit
positions are numbered left to right from most-significant to least-significant. Thus, in a 32-bit
longword, the leftmost bit, bit 31, is the most significant bit and the rightmost bit, bit 0, is the least
significant bit.

The data format in memory is shown in figure 2.7.

«
...
116
117
118
119
120
...
»

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Brand: Barracuda Networks Pages: 2

Brand: IEI Technology Pages: 21

Brand: Zonet Pages: 2

MultiConnect SE MTS2EA

Brand: Multitech Pages: 8

Brand: XtendLan Pages: 228

FastTrak TX4000

Brand: Promise Technology Pages: 76

Brand: ICP DAS USA Pages: 8

Brand: Penguin Edge Pages: 2

Brand: Acromag Pages: 23

Brand: Top Pages: 21

Brand: Renesas Pages: 4

Brand: ZyXEL Communications Pages: 2

Brand: Xilinx Pages: 43

ACC-BKT-AX-BEAM

Brand: Extreme Networks Pages: 35

Brand: XMOS Pages: 8

Brand: Rosewill Pages: 5

Brand: ADLINK Technology Pages: 69

Brand: Abov Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands