manualshive.com logo in svg

Renesas SH7763, Hardware Manual

The Renesas SH7763 Hardware Manual is an essential resource for users seeking in-depth knowledge and understanding of this versatile product. This comprehensive manual provides detailed instructions with clear diagrams and illustrations, enabling users to maximize the potential of their Renesas SH7763 device. Download it for free at manualshive.com.

Share
Download
background image

Section 8   L Memory 

 

 

Rev. 1.00  Oct. 01, 2007  Page 229 of 1956 

 

 REJ09B0256-0100 

8.3 Operation 

8.3.1 

Access from the CPU and FPU 

L memory access from the CPU and FPU is direct via the instruction bus and operand bus by 
means of the virtual address. As long as there is no conflict on the page, the L memory is accessed 
in one cycle.  

8.3.2 

Access from the SuperHyway Bus Master Module 

L memory is always accessed by the SuperHyway bus master module, such as DMAC, via the 
SuperHyway bus which is a physical address bus. The same addresses as for the virtual addresses 
must be used. 

8.3.3 Block 

Transfer 

High-speed data transfer can be performed through block transfer between the L memory and 
external memory without cache utilization.  

Data can be transferred from the external memory to the L memory through a prefetch instruction 
(PREF). Block transfer from the external memory to the L memory begins when the PREF 
instruction is issued to the address in the L memory area in the virtual address space. 

Data can be transferred from the L memory to the external memory through a write-back 
instruction (OCBWB). Block transfer from the L memory to the external memory begins when the 
OCBWB instruction is issued to the address in the L memory area in the virtual address space. 

In either case, transfer rate is fixed to 32 bytes. Since the start address is always limited to a 32-
byte boundary, the lower five bits of the address indicated by Rn are ignored, and are always dealt 
with as all 0s. In either case, other pages and cache can be accessed during block transfer, but the 
CPU will stall if the page which is being transferred is accessed before data transfer ends. 

The physical addresses [28:0] of the external memory performing data transfers with the L 
memory are specified as follows according to whether the MMU is enabled or disabled.  

(1)  When MMU is Enabled (MMUCR.AT = 1) and RAMCR.RP = 1 

An address of the L memory area is specified to the UTLB VPN field, and to the physical address 
of the transfer source (in the case of the PREF instruction) or the transfer destination (in the case 

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
Paradyne MCC Installation Instructions Manual preview
MCC
Brand: Paradyne Pages: 11
Paradyne Hotwire 8784 Installation Instructions Manual preview
Hotwire 8784
Brand: Paradyne Pages: 19
Paradyne COMSPHERE 3550 Series User Manual preview
COMSPHERE 3550 Series
Brand: Paradyne Pages: 153
Paradyne Jetstream CPX-1000 Reference Manual preview
Jetstream CPX-1000
Brand: Paradyne Pages: 141
Raidon SAFETank Series User Manual preview
SAFETank Series
Brand: Raidon Pages: 49
ekwb EK-FC1080 GTX Ti TF6 Installation Manual preview
EK-FC1080 GTX Ti TF6
Brand: ekwb Pages: 2
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
ZALMAN Extreme Gaming VGA Cooler GV1000 User Manual preview
Extreme Gaming VGA Cooler GV1000
Brand: ZALMAN Pages: 7
Renesas R0E530650CFJ30 User Manual preview
R0E530650CFJ30
Brand: Renesas Pages: 4
H3C LSWM12H2Q User Manual preview
LSWM12H2Q
Brand: H3C Pages: 9
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
NCR 7702-K134 Upgrade Manual preview
7702-K134
Brand: NCR Pages: 15
Concept Pro DEEP LEARNING PLUS Quick Start Manual preview
DEEP LEARNING PLUS
Brand: Concept Pro Pages: 28
Hama 00176547 Operating Instruction preview
00176547
Brand: Hama Pages: 25
netsys NVF-2400S User Manual preview
NVF-2400S
Brand: netsys Pages: 164
Spirent A2-400 Installation Instructions Manual preview
A2-400
Brand: Spirent Pages: 22
ETAS ES1392.1 User Manual preview
ES1392.1
Brand: ETAS Pages: 36

Brands by name

Popular brands

Load more brands