manualshive.com logo in svg

Renesas SH7763, Hardware Manual

The Renesas SH7763 Hardware Manual is an essential resource for users seeking in-depth knowledge and understanding of this versatile product. This comprehensive manual provides detailed instructions with clear diagrams and illustrations, enabling users to maximize the potential of their Renesas SH7763 device. Download it for free at manualshive.com.

Share
Download
background image

Section 9   Interrupt Controller (INTC) 

Rev. 1.00  Oct. 01, 2007  Page 292 of 1956 

REJ09B0256-0100 

 

9.4 Interrupt 

Sources 

There are four types of interrupt sources: NMI, IRQ, IRL, and on-chip modules. Each interrupt has 
a priority level (16 to 0), with level 16 as the highest and level 1 as the lowest. When level 0 is set, 
the interrupt is masked and interrupt requests are ignored. 

9.4.1 NMI 

Interrupt 

The NMI interrupt has the highest priority level of 16. It is always accepted unless the BL bit in 
SR of the CPU is set to 1. In sleep mode, the interrupt is accepted even if the BL bit is set to 1. 

A setting can also be made to have the NMI interrupt accepted even if the BL bit is set to 1. Input 
from the NMI pin is edge-detected. The NMI edge select bit (NMIE) in ICR0 is used to select 
either rising or falling edge as the detection edge. When the NMIE bit in ICR0 is modified, the 
NMI interrupt is not detected for a maximum of six bus clock cycles after the modification. If the 
INTMU bit in CPUOPM is set to 1, the IMASK value in SR is automatically set to 15 by the 
accepted NMI interrupt. If the INTMU bit in CPUOPM is set to 0, the IMASK value in SR is not 
affected by the NMI interrupt exception handling. 

9.4.2 IRQ 

Interrupts 

IRQ interrupts are available when using the IRQ7/

IRL7

 to IRQ0/

IRL0

 pin for IRQn (n = 7 to 0) 

independent interrupt inputs by setting the IRLM0 and IRLM1 bits to 1 in ICR0. The IRQnS1 and 
IRQnS0 bits in ICR1 are used to select either rising edge, falling edge, low level, or high level 
detection. A priority level can be set for each input by using the interrupt priority level setting 
register (INTPRI). 

When level detection is selected for IRQ interrupt requests, the IRQ interrupt pin input level 
should be held until the CPU accepts the interrupt and starts interrupt handling.  In level detection 
mode, after an interrupt request is accepted, the interrupt request held in the detection circuit 
should be cleared. For the specific clearing procedure, see section 9.7.3, To Clear IRQ and IRL 
Interrupt Requests. 

Note:  In level detection mode, once an IRQ interrupt request has been detected, the INTC holds 

the interrupt request as the interrupt source in INTREQ even if the corresponding IRQ 
interrupt pin level is changed to cancel the request before the CPU accepts the request. 
The interrupt source will be held until the CPU accepts any other interrupt request (IRQ or 
not) or the corresponding interrupt mask bit is set to 1. For details, see section 9.7, Usage 
Notes. 

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Lantronix Device Server UDS 10 Hardware Manual preview
Device Server UDS 10
Brand: Lantronix Pages: 8
Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
ekwb EK-FC780 GTX Jetstream Installation And Mounting Manual preview
EK-FC780 GTX Jetstream
Brand: ekwb Pages: 2
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
Garland EdgeLens INT10G8LR56 User Manual preview
EdgeLens INT10G8LR56
Brand: Garland Pages: 30
Barco Encore VPx Installation Manual preview
Encore VPx
Brand: Barco Pages: 30
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Brand: janitza Pages: 28
Patton electronics Model 2711 User Manual preview
Model 2711
Brand: Patton electronics Pages: 13
Kramer RK-10MT Quick Start Manual preview
RK-10MT
Brand: Kramer Pages: 2
Promise Technology FastTrak TX4000 User Manual preview
FastTrak TX4000
Brand: Promise Technology Pages: 76
LaView LV-KN series Quick Start Manual preview
LV-KN series
Brand: LaView Pages: 2
ADLINK Technology aTCA-9710 User Manual preview
aTCA-9710
Brand: ADLINK Technology Pages: 86
nox Hummer H-240CL Manual preview
Hummer H-240CL
Brand: nox Pages: 16
ADLINK Technology EOS-1200 User Manual preview
EOS-1200
Brand: ADLINK Technology Pages: 108
ADTRAN 1200127L1 User Manual preview
1200127L1
Brand: ADTRAN Pages: 20
Foxconn RAID Foldout Introduction preview
RAID Foldout
Brand: Foxconn Pages: 1
Acces I/O products mPCIe-ADI12-8 Hardware Manual preview
mPCIe-ADI12-8
Brand: Acces I/O products Pages: 13
National Datacomm 9210S01 User Manual preview
9210S01
Brand: National Datacomm Pages: 62

Brands by name

Popular brands

Load more brands