manualshive.com logo in svg

Renesas SH7763, Hardware Manual

The Renesas SH7763 Hardware Manual is an essential resource for users seeking in-depth knowledge and understanding of this versatile product. This comprehensive manual provides detailed instructions with clear diagrams and illustrations, enabling users to maximize the potential of their Renesas SH7763 device. Download it for free at manualshive.com.

Share
Download
background image

Section 30   SIM Card Module (SIM) 

Rev. 1.00  Oct. 01, 2007  Page 1270 of 1956 

REJ09B0256-0100 

 

Table 30.5  Example of Bit Rates (bits/s) for SCBRR Settings 

(Pck0 = 66.6 MHz, SCSMPL = 371) 

SCBRR Setting 

SCK Frequency (MHz) 

Bit Rate (bits/s) 

7 4.16 

11190 

6 4.76 

12788 

5 5.55 

14919 

4 6.66 

17903 

Note:  The bit rate is a value that is rounded off below the decimal point. 

 

30.4.5 

Data Transmit/Receive Operation 

(1) Initialization 

Prior to data transmission and reception, the following procedure should be used to initialize the 
smart card interface. Initialization is also necessary when switching from transmit mode to receive 
mode, and when switching from receive mode to transmit mode. An example of the initialization 
process is shown in the flowchart of figure 30.4. 

Step (1) to step (7) of figure 30.4 correspond to the following operation. 

1.  Clear the TE and RE bits in the serial control register (SCSCR) to 0. 

2.  Clear the error flags PER, ORER, ERS, and WAIT_ER in the serial status register (SCSSR) to 

0. 

3.  Set the parity bit (O/

E

 bit) in the serial mode register (SCSMR). 

4.  Set the LCB, PB, SMIF, SDIR, and SINV bits in the smart card mode register (SCSCMR). 

5.  Set the value corresponding to the bit rate to the bit rate register (SCBRR). 

6.  Set the clock source select bits (CKE[1] and CKE[0] bits) in the serial control register 

(SCSCR). At this time, the TIE, RIE, TE, RE, TEIE, and WAIT_IE bits should be cleared to 0. 

If the CKE[0] bit is set to 1, a clock signal is output from the SIM_CLK pin. 

7.  After waiting at least 1 etu, set the TIE, RIE, TE, RE, TEIE, and WAIT_IE bits in SCSCR. 

Except for self-check, the TE bit and RE bit should not be set simultaneously. 

 

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

ABB RELION REF615R Manual preview
RELION REF615R
Brand: ABB Pages: 66
Maco Standard Fitting Instructions Manual preview
Standard
Brand: Maco Pages: 38
FabiaTech FX5638 Series Users Quick Reference preview
FX5638 Series
Brand: FabiaTech Pages: 4
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
Commell LS-570 User Manual preview
LS-570
Brand: Commell Pages: 58
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
B&B Electronics 4 Channel Input Buffer Board SDAIBB Product Manual preview
4 Channel Input Buffer Board SDAIBB
Brand: B&B Electronics Pages: 22
Belden HIRESCHMANN IT MAMMUTHUS MTM8003-FAN User Manual preview
HIRESCHMANN IT MAMMUTHUS MTM8003-FAN
Brand: Belden Pages: 84
OWC Mercury FireWire 400 Owner'S Manual preview
Mercury FireWire 400
Brand: OWC Pages: 2
Doremi MB-4K User Manual preview
MB-4K
Brand: Doremi Pages: 15
National Instruments PXI PXITM -1000 User Manual preview
PXI PXITM -1000
Brand: National Instruments Pages: 55
Corsair LL140 RGB Series Manual preview
LL140 RGB Series
Brand: Corsair Pages: 30
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
Cowlacious Designs ISD CAP 275 Manual preview
ISD CAP 275
Brand: Cowlacious Designs Pages: 8
ADTRAN 1200127L1 User Manual preview
1200127L1
Brand: ADTRAN Pages: 20
Alphacool EISBLOCK AURORA ACRYL GPX-N RTX 3070 VENTUS INCL Instructions preview
EISBLOCK AURORA ACRYL GPX-N RTX 3070 VENTUS INCL
Brand: Alphacool Pages: 3
Dahua Technology VDA-NVR2108W4KS2 User Manual preview
VDA-NVR2108W4KS2
Brand: Dahua Technology Pages: 363

Brands by name

Popular brands

Load more brands