manualshive.com logo in svg

Renesas SH7763, Hardware Manual

The Renesas SH7763 Hardware Manual is an essential resource for users seeking in-depth knowledge and understanding of this versatile product. This comprehensive manual provides detailed instructions with clear diagrams and illustrations, enabling users to maximize the potential of their Renesas SH7763 device. Download it for free at manualshive.com.

Share
Download
background image

Section 11   Local Bus State Controller (LBSC) 

Rev. 1.00  Oct. 01, 2007  Page 386 of 1956 

REJ09B0256-0100 

 

11.5.6 MPX 

Interface 

When both the MODE4 and MODE3 pins are set to 0 at a power-on reset by the 

PRESET

 pin, the 

MPX interface is selected for area 0. The MPX interface is selected for areas 1, 2, and 4 to 6 by 
the MPX bit in CS1BCR, CS2BCR, and CS4BCR to CS6BCR. The MPX interface provides an 
address/data multiplex-type bus protocol and facilitates connection with external memory 
controller chips using an address/data multiplex-type 32-bit single bus. A bus cycle consists of an 
address phase and a data phase. Address information is output on D25 to D0 and the access size is 
output on D31 to D29 in the address phase. The 

BS

 signal is asserted for one cycle to indicate the 

address phase. The 

CSn

 signal is asserted at the rising edge in Tm1 and is negated after the end of 

the last data transfer in the data phase. Therefore, a negation cycle does not occur in the case of 
minimum pitch access. The 

FRAME

 signal is asserted at the rising edge in Tm1 and negated at the 

start of the last data transfer cycle in the data phase. Therefore, an external device for the MPX 
interface must internally store the address information and access size output in the address phase 
and perform data input/output for the data phase. For details, see section 11.5.1, Endian/Access 
Size and Data Alignment. 

Values output on address pins A25 to A20 are not guaranteed. 

In 32-byte transfer, a total of 32 bytes are transferred continuously according to the set bus width. 
The first access is performed on the data for which there was an access request, and the remaining 
accesses are performed according to the set bus width. If the access size is larger than the bus 
width in this case, a burst access with continuing multiple data cycle occurs after one address 
output. The bus is not released during this transfer. 

D31  D30 D29 Access 

Size 

0  0 0 Byte 

  

1 

Word 

 

1 0 Longword 

  

1 

Quadword 

1  X X 32-byte 

burst 

[Legend] 

X: Don't 

care 

 

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
Idis DR-8416 Operation Manual preview
DR-8416
Brand: Idis Pages: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Brand: Idis Pages: 29
Idis DR-4516P Installation Manual preview
DR-4516P
Brand: Idis Pages: 28
Idis DirectIP DR-1304P Operation Manual preview
DirectIP DR-1304P
Brand: Idis Pages: 82
IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
Dazzle Hollywood DV-Bridge User Manual preview
Hollywood DV-Bridge
Brand: Dazzle Pages: 63
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Brand: Ubiquiti Pages: 13
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Brand: Patton electronics Pages: 145
Acromag APCe7012E-LF User Manual preview
APCe7012E-LF
Brand: Acromag Pages: 23
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Brand: ICS ELECTRONICS Pages: 4
Harman BSS DCP-555 Installation Manual preview
BSS DCP-555
Brand: Harman Pages: 24
ICP ICP9014RO Installation And User Manual preview
ICP9014RO
Brand: ICP Pages: 142

Brands by name

Popular brands

Load more brands