manualshive.com logo in svg

Renesas SH7763, Hardware Manual

The Renesas SH7763 Hardware Manual is an essential resource for users seeking in-depth knowledge and understanding of this versatile product. This comprehensive manual provides detailed instructions with clear diagrams and illustrations, enabling users to maximize the potential of their Renesas SH7763 device. Download it for free at manualshive.com.

Share
Download
background image

Section 26   I

2

C Bus Interface (IIC) 

Rev. 1.00  Oct. 01, 2007  Page 1036 of 1956 

REJ09B0256-0100 

 

26.3.5 Master 

Control Register (ICMCR) 

7

6

5

4

3

2

1

0

0

0

0

0

0

0

R

R/W

R/W

R/W

R/W

R/W

R/W

R/W

BIt:

Initial value:

R/W:

MDBS

FSCL

FSDA

OBPC

MIE

TSBE

FSB

ESG

−

−

 

 

Bit 

Bit Name 

Initial Value 

R/W 

Description 

7 

MDBS 

0 

R/W 

Master Data Buffer Select 

This bit is used to select the data buffer. The 
double-buffer mode and singe-buffer mode are 
available. 

When this bit is set to 0, the double-buffer 
mode is selected. During a reception, as long 
as both buffers are full and the MDR flag has 
not been cleared, SCL is held low. When the 
MDR flag is cleared, the low level state of SCL 
is released. 

When this bit is set to 1, the single-buffer mode 
is selected. SCL will be held low from the 
timing when the receive data register acquires 
the data packet until the MDR flag is cleared. 

0: Double-buffer mode 

1: Single-buffer mode 

6 

FSCL 

— 

R/W 

Forced SCL  

This bit controls the status of the I2C_SCL pin 
(reading reflects the current level on the I

2

C 

bus). When the OBPC bit is set, this bit directly 
controls the SCL line on the bus. 

During a read cycle, the level on this bit (which 
includes the reset level) will change depending 
on the level on I2C_SCL since it reflects the 
level on the I2C_SCL. 

5 FSDA 

— 

R/W 

Forced 

SDA 

This bit controls the status of the I2C_SDA pin 
(reading reflects the busy status level on the 
I2C_SDA). When the OBPC bit is set then this 
bit directly controls the SDA line on the bus. 

During a read cycle, the level of this bit (which 
includes the reset level) will show the busy 
status of the I

2

C bus (1 for busy; 0 for not 

busy). 

 

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Yaesu FT-817 - Modification Instructions preview
FT-817 -
Brand: Yaesu Pages: 2
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
hawa HAWA-Frontside 60/B Planning And Installation Instructions preview
HAWA-Frontside 60/B
Brand: hawa Pages: 28
Alacritech 1000x1 Hardware Installation Manual preview
1000x1
Brand: Alacritech Pages: 20
Aqua Computer Aquaduct 360 XT Operating And Assembly Manual preview
Aquaduct 360 XT
Brand: Aqua Computer Pages: 28
ENERMAX ELC-LTTR240-TBP User Manual preview
ELC-LTTR240-TBP
Brand: ENERMAX Pages: 16
IBASE Technology FWA8207 Series User Manual preview
FWA8207 Series
Brand: IBASE Technology Pages: 39
A4Tech RH-10 User Manual preview
RH-10
Brand: A4Tech Pages: 8
Hauppauge WinTV-DVB Installation And Reference Manual preview
WinTV-DVB
Brand: Hauppauge Pages: 62
Altera Stratix II User Manual preview
Stratix II
Brand: Altera Pages: 33
FiberHome AN5506-04-B User Manual preview
AN5506-04-B
Brand: FiberHome Pages: 44
Aleratec 260206 Quick Start Manual preview
260206
Brand: Aleratec Pages: 16
H3C SecPath F50X0 Series Manual preview
SecPath F50X0 Series
Brand: H3C Pages: 41
SIIG SATA II-150 PCI Quick Installation Manual preview
SATA II-150 PCI
Brand: SIIG Pages: 16
nox Hummer H-240CL Manual preview
Hummer H-240CL
Brand: nox Pages: 16
Transition Networks E-BR-SIC User Manual preview
E-BR-SIC
Brand: Transition Networks Pages: 1
Atmel SAMA5D31-EK User Manual preview
SAMA5D31-EK
Brand: Atmel Pages: 123
INGENIA Everest CORE Product Manual preview
Everest CORE
Brand: INGENIA Pages: 58

Brands by name

Popular brands

Load more brands