manualshive.com logo in svg

Renesas SH7763, Hardware Manual

The Renesas SH7763 Hardware Manual is an essential resource for users seeking in-depth knowledge and understanding of this versatile product. This comprehensive manual provides detailed instructions with clear diagrams and illustrations, enabling users to maximize the potential of their Renesas SH7763 device. Download it for free at manualshive.com.

Share
Download
background image

Section 26   I

2

C Bus Interface (IIC) 

 

 

Rev. 1.00  Oct. 01, 2007  Page 1055 of 1956 

 

 REJ09B0256-0100 

3.  Reset the MDE bit. 

Clear MDE after setting the last byte to be transmitted. After the last byte data is transmitted, 
MDE is generated.  To clear the MDE, you must set the master control register to H'8A. 

(Set the force stop control bit). 

 

(5)  Wait for End of Transmission 

1.  Wait for the master event, MST in the master status register. 

2.  Reset the MST bit after confirming MNR (Master NACK Received). 

 

26.5.2 Master 

Receiver 

To set up the master interface to receive a data packet on the I

2

C bus, follow the following 

procedure: 

(1)  Load Clock Control Register 

1.  SCL clock generation divider (SCGD) 

=

 H'03 

(SCL frequency of 400 kHz). 

2.  Clock division ratio (CDF) 

=

 H'3 

(The peripheral clock is 66.7 MHz and the IIC's internal clock IICck is 16.7 MHz.) 

 

(2)  Load Master Control Register and Address 

1.  Set master address register to address of slave being accessed and STM1 bit (read mode: 1). 

2.  Set master control register to H'89 

(MDBS 

=

 1, MIE 

=

 1, ESG 

=

 1). 

 

(3)  Wait for Outputting Address 

1.  Wait for master event (an interrupt of the MAT and MDR bits in the master status register). 

2.  Set the master control register to H'88 

(To suspend the data transmission, the master device will hold the SCL low until the MDR bit 
is cleared). 

If only one byte of data is received, set the master control register to H'8A, meaning that the 
stop generation is enabled. This generates a stop on the bus as soon as one byte has been 
received. 

3.  Reset the MAT bit. 

 

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
H3C H3C S7500E Series Instruction Manual preview
H3C S7500E Series
Brand: H3C Pages: 34
H3C SR8800 IM-FW-II Manual preview
SR8800 IM-FW-II
Brand: H3C Pages: 5
H3C H3C S7500E Series Installation Manual preview
H3C S7500E Series
Brand: H3C Pages: 50
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Brand: Ublox Pages: 116
Lanner NCA-2510 Installation Manual preview
NCA-2510
Brand: Lanner Pages: 2
IDT TSI384 User Manual preview
TSI384
Brand: IDT Pages: 281
DMX4ALL DMX-Universal-Demux User Manual preview
DMX-Universal-Demux
Brand: DMX4ALL Pages: 17
Rockwell Automation 41LR4060 Instruction Manual preview
41LR4060
Brand: Rockwell Automation Pages: 108
AXIOMTEK eBOX532-100-FL Series Quick Installation Manual preview
eBOX532-100-FL Series
Brand: AXIOMTEK Pages: 2
Kontron 50099 067 User Manual preview
50099 067
Brand: Kontron Pages: 42
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Brand: Lindsay Broadband Pages: 4
Aaeon SBC-657B Manual preview
SBC-657B
Brand: Aaeon Pages: 61
Kramer RK-10MT Quick Start Manual preview
RK-10MT
Brand: Kramer Pages: 2
Softing TH LINK Installation Manual preview
TH LINK
Brand: Softing Pages: 16
Idis DR-2308P Quick Manual preview
DR-2308P
Brand: Idis Pages: 18

Brands by name

Popular brands

Load more brands