manualshive.com logo in svg

Renesas SH7763, Hardware Manual

The Renesas SH7763 Hardware Manual is an essential resource for users seeking in-depth knowledge and understanding of this versatile product. This comprehensive manual provides detailed instructions with clear diagrams and illustrations, enabling users to maximize the potential of their Renesas SH7763 device. Download it for free at manualshive.com.

Share
Download
background image

Section 28   Serial Communication Interface with FIFO/IrDA Interface (SCIF/IrDA) 

 

 

Rev. 1.00  Oct. 01, 2007  Page 1167 of 1956 

 

 REJ09B0256-0100 

Figure 28.13 shows a sample SCIF initialization flowchart. 

Start of initialization

Clear TE and RE bits 

in SCSCR to 0 

Set 

TFCL and RFCL bits 

in SCFCR to 1 to clear 

the FIFO buffer  

After reading BRK, DR, 

and ER flags in SCFSR, and 

ORER flag in SCLSR, 

write 0 to clear them  

Set CKE1 and CKE0 bits  

in SCSCR (leaving TE, RE, TIE, 

and RIE bits cleared to 0) 

Set data transfer format  

in SCSMR

Set value in SCBRR

1-bit interval elapsed?

Set RTRG1-0 and TTRG1-0 bits 

in SCFCR, and clear TFCL 

and RFCL bits to 0  

Set TE and RE bits in SCSCR  

to 1, and set TIE, RIE, 

and REIE bits 

End of initialization

Wait

No

Yes

Leave the TE and RE bits cleared to 0 until the 
initialization almost ends. 

Set the CKE1 and CKE0 bits.

Set the data transfer/receive format in SCSMR.

Write a value corresponding to the bit rate into SCBRR. 
This is not necessary if an external clock is used. 
Wait at least one bit interval after this write before moving 
to the next step.

Set the TE or RE bit in SCSCR to 1. Also set the TIE, RIE, 
and REIE bits to enable the SCIF_TXD, SCIF_RXD, 
and SCIF_CLK pins to be used. When transmitting, 
the SCIF_TXD pin will go to the mark state. When 
receiving in clocked synchronous mode with the 
synchronization clock output (clock master) selected, 
a clock starts to be output from the SCIFn_SCK pin
at this point.

[1]

[1]

[2]

[3]

[4]

[5]

[2]

[3]

[4]

[5]

 

Figure 28.13   Sample SCIF Initialization Flowchart 

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

LAWO edge User Manual preview
edge
Brand: LAWO Pages: 154
IBM LS42 - BladeCenter - 7902 Installation Manual preview
LS42 - BladeCenter - 7902
Brand: IBM Pages: 56
IBM ATA 133 Quick Hardware Setup Manual preview
ATA 133
Brand: IBM Pages: 2
IBM BladeCenter Management Module User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 78
IBM 9040-MR9 Manual preview
9040-MR9
Brand: IBM Pages: 110
IBM Remote Supervisor Adapter II User Manual preview
Remote Supervisor Adapter II
Brand: IBM Pages: 132
National Instruments PXIe-8240 Getting Started preview
PXIe-8240
Brand: National Instruments Pages: 9
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Brand: National Instruments Pages: 8
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
Phytec L-843e.A1 Hardware Manual preview
L-843e.A1
Brand: Phytec Pages: 53
ZyXEL Communications EOC350 Series Quick Start Manual preview
EOC350 Series
Brand: ZyXEL Communications Pages: 2
Dahua NVS0X04DH Quick Start Manual preview
NVS0X04DH
Brand: Dahua Pages: 24
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
Juniper NFX250 Quick Start Manual preview
NFX250
Brand: Juniper Pages: 7
Adaptec AAA-130SA SERIES Installation And Hardware Manual preview
AAA-130SA SERIES
Brand: Adaptec Pages: 94
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
Aewin Technologies SCB-9651 User Manual preview
SCB-9651
Brand: Aewin Technologies Pages: 86
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Brand: ZALMAN Pages: 18

Brands by name

Popular brands

Load more brands