manualshive.com logo in svg

Renesas SH7763, Hardware Manual

The Renesas SH7763 Hardware Manual is an essential resource for users seeking in-depth knowledge and understanding of this versatile product. This comprehensive manual provides detailed instructions with clear diagrams and illustrations, enabling users to maximize the potential of their Renesas SH7763 device. Download it for free at manualshive.com.

Share
Download
background image

Section 41   User Break Controller (UBC) 

Rev. 1.00  Oct. 01, 2007  Page 1782 of 1956 

REJ09B0256-0100 

 

41.3.2 

User Break Operation Sequence 

The following describes the sequence from when the break condition is set until the user break 
exception handling is initiated.   

1.  Specify the operand size, bus, instruction fetch/operand access, and read/write as the match 

conditions using the match condition setting register (CBR0 or CBR1).  Specify the break 
address using the match address setting register (CAR0 or CAR1), and specify the address 
mask condition using the match address mask setting register (CAMR0 or CAMR1).  To 
include the ASID in the match conditions, set the AIE bit in the match condition setting 
register and specify the ASID value by the AIV bit in the same register.  To include the data 
value in the match conditions, set the DBE bit in the match condition setting register; specify 
the break data using the match data setting register (CDR1); and specify the data mask 
condition using the match data mask setting register (CDMR1).  To include the execution 
count in the match conditions, set the ETBE bit of the match condition setting register; and 
specify the execution count using the execution count break register (CETR1).  To use the 
sequential break, set the MFE bit of the match condition setting register; and specify the 
number of the first channel using the MFI bit.  

2.  Specify whether or not to request a break when the match condition is satisfied and the break 

timing when the match condition is satisfied as a result of fetching the instruction using the 
match operation setting register (CRR0 or CRR1).  After having set all the bits in the match 
condition setting register except the CE bit and the other necessary registers, set the CE bit and 
read the match condition setting register again.  This ensures that the set values in the control 
registers are valid for the subsequent instructions immediately after reading the register.  
Setting the CE bit of the match condition setting register in the initial state after reset via the 
control registers may cause an undesired break. 

3.  When the match condition has been satisfied, the corresponding condition match flag (MF1 or 

MF0) in the channel match flag register (CCMFR) is set.  A break is also requested to the CPU 
according to the set values in the match operation setting register (CRR0 or CRR1).  The CPU 
operates differently according to the BL bit value of the SR register: when the BL bit is 0, the 
CPU accepts the break request and executes the specified exception handling; and when the 
BL bit is 1, the CPU does not execute the exception handling.   

4.  The match flags (MF1 and MF0) can be used to confirm whether or not the corresponding 

match condition has been satisfied.  Although the flag is set when the condition is satisfied, it 
is not cleared automatically; therefore, write 0 to the flag bit by issuing a memory store 
instruction to the channel match flag register (CCMFR) in order to use the flag again.   

5.  Breaks may occur virtually at the same time for channels 0 and 1.  In this case, only one break 

request is sent to the CPU; however, the two condition match flags corresponding to these 
breaks may be set. 

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Hal Communications RS2100 Instruction Manual preview
RS2100
Brand: Hal Communications Pages: 25
Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
Acconeer A111 User Manual preview
A111
Brand: Acconeer Pages: 32
NAIM AV2 Update Instructions preview
AV2
Brand: NAIM Pages: 2
VAF instruments 667 Instructions For Installation, Operation And Maintenance preview
667
Brand: VAF instruments Pages: 56
Hama 39707 Operating Instruction preview
39707
Brand: Hama Pages: 4
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
Ubiquiti PBE-5AC-300-ISO Quick Start Manual preview
PBE-5AC-300-ISO
Brand: Ubiquiti Pages: 28
ZALMAN CNPS12X User Manual preview
CNPS12X
Brand: ZALMAN Pages: 11
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
ZiLOG Z8 GP ZGP323 User Manual preview
Z8 GP ZGP323
Brand: ZiLOG Pages: 11
Icy Box IB-NAS5520 Quick Start Manual preview
IB-NAS5520
Brand: Icy Box Pages: 2
OPTO 22 PCI-AC48 User Manual preview
PCI-AC48
Brand: OPTO 22 Pages: 28
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Brand: PairGain Pages: 48
Honeywell Home LTEM-PA Installation And Setup Manual preview
LTEM-PA
Brand: Honeywell Home Pages: 36
Positron TeleLite 720920 Series Manual preview
TeleLite 720920 Series
Brand: Positron Pages: 21
Atmel SAMA5D31-EK User Manual preview
SAMA5D31-EK
Brand: Atmel Pages: 123

Brands by name

Popular brands

Load more brands