Renesas SH7763 Hardware Manual Download Page 1334 | Manualshive

Page: 1334 / 2026

background image

Section 30 SIM Card Module (SIM)

Rev. 1.00 Oct. 01, 2007 Page 1268 of 1956

REJ09B0256-0100

Table 30.4 Register Settings for Smart Card Interface

Bit

Register

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

SCSMR 0 0 PE O/

E

0

0

0

0

SCBRR 0 0 0 0 0

BRR2

BRR1 BRR0

SCSCR

TIE

RIE

TE

RE

WAIT_IE TEIE

CKE1

CKE0

SCTDR SCTD7

SCTD6

SCTD5

SCTD4

SCTD3

SCTD2

SCTD1

SCTD0

SCSSR TDRE

RDRF

ORER

ERS

PER TEND

WAIT_ER

0

SCRDR SCRD7

SCRD6

SCRD5

SCRD4

SCRD3

SCRD2

SCRD1

SCRD0

SCSCMR 0

LCB PB 0

SDIR SINV RST

1

SCSC2R EIO 0

0

0

0

0

0

0

SCWAIT

SCWAIT15 to SCWAIT0

SCGRD

SCGRD7 to SCGRD0

SCSMPL

SCSMPL10 to SCSMPL0, bits 11 to 15 are 0

•

Serial mode register (SCSMR) setting

When the IC card is set for the direct convention, the O/

E

bit is cleared to 0; for the inverse

convention, it is set to 1.

•

Bit rate register (SCBRR) setting

Sets the bit rate. For the method of computing settings, refer to section 30.4.4, Clocks.

•

Serial control register (SCSCR) settings

Each interrupt can be enabled and disabled using the TIE, RIE, TEIE, and WAIT_IE bits.

By setting either the TE or RE bit to 1, transmission or reception is selected.

The CKE[1] and CKE[0] bits are used to select the clock output state. For details, refer to
section 30.4.4, Clocks.

•

Smart card mode register (SCSCMR) settings

When the IC card is set for the direct convention, both the SDIR and SINV bits are cleared to
0; for the inverse convention, both are set to 1. The SMIF bit is always set to 1.

Figure 30.3 below shows the register settings and waveform examples at the start character for
two types of IC cards (a direct-convention type and an inverse-convention type).

For the direct-convention type, the logical level 1 is assigned to the Z state, and the logical
level 0 to the A state, and transmission and reception are performed in LSB-first. The data of
the above start character is then H'3B. Even parity is used according to the smart card
specification, and so the parity bit is 1.

«
...
1332
1333
1334
1335
1336
...
»

Summary of Contents for SH7763











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7763

Brand: STONEFLY Pages: 48

Brand: Freescale Semiconductor Pages: 921

Brand: Analog Devices Pages: 76

Brand: Dantel Pages: 62

Brand: Cypress Semiconductor Pages: 16

Brand: MC Pages: 21

4 Channel Input Buffer Board SDAIBB

Brand: B&B Electronics Pages: 22

PCM-4141 Series

Brand: Advantech Pages: 96

Brand: ICOP Technology Pages: 34

Brand: Compal Pages: 47

Brand: Microtek Pages: 25

Brand: Renesas Pages: 4

Brand: PairGain Pages: 48

Brand: ADLINK Technology Pages: 86

Brand: Renesas Pages: 7

Brand: Honeywell Home Pages: 36

Brand: Hama Pages: 34

PMP/PTP 450 Series

Brand: Cambium Networks Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands