manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 22 FlexCAN

MPC5602P Microcontroller Reference Manual, Rev. 4

550

Freescale Semiconductor

 

20

RWRN_MSK

Rx Warning Interrupt Mask
This bit provides a mask for the Rx Warning Interrupt associated with the RWRN_INT flag in the 
Error and Status Register. This bit has no effect if the WRN_EN bit in MCR is negated and it is read 
as zero when WRN_EN is negated.
0 Rx Warning Interrupt disabled.
1 Rx Warning Interrupt enabled.

21

LPB

Loop Back
This bit configures FlexCAN to operate in Loop-Back Mode. In this mode, FlexCAN performs an 
internal loop back that can be used for self test operation. The bit stream output of the transmitter 
is fed back internally to the receiver input. The Rx CAN input pin is ignored and the Tx CAN output 
goes to the recessive state (logic 1). FlexCAN behaves as it normally does when transmitting, and 
treats its own transmitted message as a message received from a remote node. In this mode, 
FlexCAN ignores the bit sent during the ACK slot in the CAN frame acknowledge field, generating 
an internal acknowledge bit to ensure proper reception of its own message. Both transmit and 
receive interrupts are generated.
0 Loop Back disabled. 
1 Loop Back enabled. 

24

SMP

Sampling Mode
This bit defines the sampling mode of CAN bits at the Rx input. 
0 Just one sample determines the bit value. 
1 Three samples are used to determine the value of the received bit: the regular one (sample point) 

and two preceding samples, a majority rule is used. 

25

BOFF_REC

Bus Off Recovery Mode
This bit defines how FlexCAN recovers from Bus Off state. If this bit is negated, automatic 
recovering from Bus Off state occurs according to the CAN Specification 2.0B. If the bit is asserted, 
automatic recovering from Bus Off is disabled and the module remains in Bus Off state until the bit 
is negated by the user. If the negation occurs before 128 sequences of 11 recessive bits are 
detected on the CAN bus, then Bus Off recovery happens as if the BOFF_REC bit had never been 
asserted. If the negation occurs after 128 sequences of 11 recessive bits occurred, then FlexCAN 
will resynchronize to the bus by waiting for 11 recessive bits before joining the bus. After negation, 
the BOFF_REC bit can be re-asserted again during Bus Off, but it will only be effective the next time 
the module enters Bus Off. If BOFF_REC was negated when the module entered Bus Off, asserting 
it during Bus Off will not be effective for the current Bus Off recovery.
0 Automatic recovering from Bus Off state enabled, according to CAN Spec 2.0 part B. 
1 Automatic recovering from Bus Off state disabled. 

26

TSYN

Timer Sync Mode
This bit enables a mechanism that resets the free-running timer each time a message is received 
in Message Buffer 0. This feature provides means to synchronize multiple FlexCAN stations with a 
special “SYNC” message (that is, global network time). If the FEN bit in MCR is set (FIFO enabled), 
MB8 is used for timer synchronization instead of MB0.
0 Timer Sync feature disabled
1 Timer Sync feature enabled

27

LBUF

Lowest Buffer Transmitted First 
This bit defines the ordering mechanism for Message Buffer transmission. When asserted, the 
LPRIO_EN bit does not affect the priority arbitration.
0 Buffer with highest priority is transmitted first. 
1 Lowest number buffer is transmitted first. 

Table 22-13. CTRL field descriptions (continued)

Field

Description

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

H3C WX Series Configuration Manual preview
WX Series
Brand: H3C Pages: 69
Samson 3730-6 Mounting And Operating Instructions preview
3730-6
Brand: Samson Pages: 124
Samson TROVIS 5500 Operating Instructions Manual preview
TROVIS 5500
Brand: Samson Pages: 86
VAC V100 Troubleshooting Manual preview
V100
Brand: VAC Pages: 5
YOKOGAWA TC 10-L Engineering Manual preview
TC 10-L
Brand: YOKOGAWA Pages: 20
YOKOGAWA UTAdvanced UT32A Technical Information preview
UTAdvanced UT32A
Brand: YOKOGAWA Pages: 3
AAF MicroTech II UV05 Operation & Maintenance Manual preview
MicroTech II UV05
Brand: AAF Pages: 50
Elby Designs ASM301-ADSR Diagrams preview
ASM301-ADSR
Brand: Elby Designs Pages: 4
A & H AMFLOW A2-ACM Installation, Operation & Service Manual preview
AMFLOW A2-ACM
Brand: A & H Pages: 35
MegaLite MEMO CORE CONTROL User Manual preview
MEMO CORE CONTROL
Brand: MegaLite Pages: 11
zeeltronic PDCI-24V User Manual preview
PDCI-24V
Brand: zeeltronic Pages: 13
QD Dynamics Pi HSC505-32 User'S Information Manual preview
Pi HSC505-32
Brand: QD Dynamics Pages: 64
Kustom Signals Eyewitness HD ICV System Quick Reference Manual preview
Eyewitness HD ICV System
Brand: Kustom Signals Pages: 4
Topcon OPUS A3 STANDARD Full Technical Data Sheet preview
OPUS A3 STANDARD Full
Brand: Topcon Pages: 10
Watlow Integrated Controller Rev C EZ-ZONE PM User Manual preview
Integrated Controller Rev C EZ-ZONE PM
Brand: Watlow Pages: 80
Pellet Grill Outlet 180-LV Installation Instructions And User Manual preview
180-LV
Brand: Pellet Grill Outlet Pages: 4
Samson Graphite MF8 Quick Start Manual preview
Graphite MF8
Brand: Samson Pages: 64
SystemAir NOTUS-R Installation, Maintenance And Operation Instructions preview
NOTUS-R
Brand: SystemAir Pages: 4

Brands by name

Popular brands

Load more brands