manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 21 LIN Controller (LINFlex)

MPC5602P Microcontroller Reference Manual, Rev. 4

500

Freescale Semiconductor

 

t

Table 21-8. LINSR field descriptions

Field

Description

LINS

LIN modes / normal mode states

0000: Sleep mode

LINFlex is in Sleep mode to save power consumption.

0001: Initialization mode

LINFlex is in Initialization mode.

Normal mode states

0010: Idle

This state is entered on several events:
 • SLEEP bit and INIT bit in LINCR1 have been cleared by software,
 • A falling edge has been received on RX pin and AWUM bit is set,
 • The previous frame reception or transmission has been completed or aborted.

0011: Break

In Slave mode, a falling edge followed by a dominant state has been detected. Receiving Break.

Note:

In Slave mode, in case of error new LIN state can be either Idle or Break depending on 
last bit state. If last bit is dominant new LIN state is Break, otherwise Idle.

In Master mode, Break transmission ongoing.

0100: Break Delimiter

In Slave mode, a valid Break has been detected. See 

Section 21.7.1.1, LIN control register 1 

(LINCR1)

 for break length configuration (10-bit or 11-bit). Waiting for a rising edge.

In Master mode, Break transmission has been completed. Break Delimiter transmission is 
ongoing.

0101: Synch Field

In Slave mode, a valid Break Delimiter has been detected (recessive state for at least one bit 
time). Receiving Synch Field.
In Master mode, Synch Field transmission is ongoing.

0110: Identifier Field

In Slave mode, a valid Synch Field has been received. Receiving Identifier Field.
In Master mode, identifier transmission is ongoing.

0111: Header reception/transmission completed

In Slave mode, a valid header has been received and identifier field is available in the BIDR.
In Master mode, header transmission is completed.

1000: Data reception/transmission

Response reception/transmission is ongoing.

1001: Checksum

Data reception/transmission completed. Checksum reception/transmission ongoing.
In UART mode, only the following states are flagged by the LIN state bits:
  • Init
 • Sleep
  • Idle
 • Data transmission/reception

RMB

Release Message Buffer
0 Buffer is free.
1 Buffer ready to be read by software. This bit must be cleared by software after reading data 

received in the buffer.

This bit is cleared by hardware in Initialization mode.

RBSY

Receiver Busy Flag
0 Receiver is idle
1 Reception ongoing

Note:

In Slave mode, after header reception, if BIDR[DIR] = 0 and reception starts then this bit 
is set. In this case, user cannot program LINCR2[DTRQ] = 1.

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

BADODOSECURITY G200 Quick Manual preview
G200
Brand: BADODOSECURITY Pages: 8
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Brand: IBC Pages: 8
Centurion TB-CN2R1 Instruction Manual preview
TB-CN2R1
Brand: Centurion Pages: 16
CORNING Ascent 6970 Instruction Manual preview
Ascent 6970
Brand: CORNING Pages: 142
Swagelok TBVS4 User Manual preview
TBVS4
Brand: Swagelok Pages: 16
KBR multicomp F144-MS-1V1C1TI6RO-3 User Manual preview
multicomp F144-MS-1V1C1TI6RO-3
Brand: KBR Pages: 68
QUANT QUANT-14 Operation Manual preview
QUANT-14
Brand: QUANT Pages: 24
Aurora Scientific 315D Instruction Manual preview
315D
Brand: Aurora Scientific Pages: 21
Clare Controls CLIQ.host Installation Sheet preview
CLIQ.host
Brand: Clare Controls Pages: 3
Swegon TACTouch TAC5 Manual preview
TACTouch TAC5
Brand: Swegon Pages: 11
Danfoss AK-PC 420 Instructions Manual preview
AK-PC 420
Brand: Danfoss Pages: 18
Viking C-2000B Product Manua preview
C-2000B
Brand: Viking Pages: 24
Mophie 1190_RCN-RMT-BLk User Manual preview
1190_RCN-RMT-BLk
Brand: Mophie Pages: 10
YASKAWA U1000 iQpump Drive Technical Manual preview
U1000 iQpump Drive
Brand: YASKAWA Pages: 706
Sensor Access IC2001 Manual preview
IC2001
Brand: Sensor Access Pages: 11
cashco 764P Nstallation, Operation & Maintenance Manual preview
764P
Brand: cashco Pages: 14
FCS FWC-1101 Installation Manual preview
FWC-1101
Brand: FCS Pages: 6
3Ware 720-0127-02 Manual preview
720-0127-02
Brand: 3Ware Pages: 122

Brands by name

Popular brands

Load more brands