manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 84

Chapter 4 Clock Description

MPC5602P Microcontroller Reference Manual, Rev. 4

84

Freescale Semiconductor

 

4.3

Alternate module clock domains

This section lists the different clock domains for each module. If not otherwise noted, all modules on the 
MPC5602P device are clocked on the SYS_CLK.

4.3.1

FlexCAN clock domains

The FlexCAN modules have two distinct software controlled clock domains. One of the clock domains is 
always derived from the system clock. This clock domain includes the message buffer logic. The source 
for the second clock domain can be either the system clock (SYS_CLK) or a direct feed from the oscillator 
pin XOSC_CLK. The logic in the second clock domain controls the CAN interface pins. The CLK_SRC 
bit in the FlexCAN CTRL register selects between the system clock and the oscillator clock as the clock 
source for the second domain. Selecting the oscillator as the clock source ensures very low jitter on the 
CAN bus. System software can gate both clocks by writing to the MDIS bit in the FlexCAN MCR. 

Figure 22-1

 shows the two clock domains in the FlexCAN modules.

Refer to 

Chapter 22, “FlexCAN

 for more information on the FlexCAN modules.

4.3.2

SWT clock domains

The SWT module has two distinct clock domains. The first clock domain (Module Clock) is always 
supplied from the SYS_CLK. This clock domain includes the register interface. 

The source for the second clock domain (Protocol Clock) is always the IRC generated by the internal RC 
oscillator.

4.3.3

Cross Triggering Unit (CTU) clock domains

The CTU module has two distinct clock domains. The first clock domain (Module Clock) is supplied from 
the SYS_CLK. This clock domain includes the Command Buffer logic. 

The source for the second clock domain (Protocol Clock) is the MC_PLL_CLK. The logic in the Protocol 
Clock domain controls the CTU interface pins to the eTimer module and the ADC module.

4.3.4

Peripherals behind the IPS bus clock sync bridge

4.3.4.1

FlexPWM clock domain

The FlexPWM module has only one clock domain. The FlexPWM module is clocked from the 
MC_PLL_CLK. Therefore, it is placed behind the IPS bus clock sync bridge.

4.3.4.2

eTimer_0 clock domain

The eTimer_0 module has only one clock domain. The eTimer_0 module is clocked from the 
MC_PLL_CLK. Therefore, it is placed behind the IPS bus clock sync bridge.

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands