manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 36 Nexus Development Interface (NDI)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

923

 

0100: Subtract 0x10 from PC.
0101: Subtract 0x14 from PC.
all other encodings are reserved

* — Internal State Bits

These control bits represent internal processor state and should be restored to their original value after a 
debug session is completed, i.e when a e200z0h OnCE command is issued with the GO and EX bits set 
and not ignored. When performing instruction execution during a debug session (see 

Section 36.12.4.3, 

“e200z0h OnCE Debug Output (jd_debug_b)

) which is not part of the normal program execution flow, 

these bits should be set to a 0.

PCINV — PC and IR Invalid Status Bit

This status bit indicates that the values in the IR and PC portions of the CPUSCR are invalid. Exiting debug 
mode with the saved values in the PC and IR will have unpredictable results. Debug firmware should 
initialize the PC and IR values in the CPUSCR with desired values prior to exiting debug mode if this bit 
was set when debug mode was initially entered.

0: No error condition exists.
1: Error condition exists. PC and IR are corrupted.

FFRA— Feed Forward RA Operand Bit

This control bit causes the content of the WBBR

low 

to be used as the RA This control bit causes the content 

of the WBBR

 

to be used as the RA operand value (RS for logical, mtspr, mtdcr, cntlzw, and shift 

operations, RX for VLE se_ instructions, RT for e_{logical_op}2i type instructions, and the value to use 
as the PC for calculating the LR update value for branch with link type instructions) of the first instruction 
to be executed following an update of the CPUSCR. This allows the debug firmware to update processor 
registers — initialize the WBBR with the desired value, set the FFRA bit, and execute a ori Rx,Rx,0 
instruction to the desired register.

0: No action.
1: Content of WBBR

low

 used as operand value

IRStat0 — IR Status Bit 0

This control bit indicates a TEA status for the IR. 

0: No TEA occurred on the fetch of this instruction.
1: TEA occurred on the fetch of this instruction.

IRStat1 — IR Status Bit 1

This control bit indicates a TLB Miss status for the IR. (Note that this bit is reserved.)

0: No TLB Miss occurred on the fetch of this instruction.
1: TLB Miss occurred on the fetch of this instruction.

IRStat2 — IR Status Bit 2

This control bit indicates an Instruction Address Compare 1 event status for the IR. 

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

C Prox Ltd FP1 User Manual preview
FP1
Brand: C Prox Ltd Pages: 5
Lattice Semiconductor HDR-60 User Manual preview
HDR-60
Brand: Lattice Semiconductor Pages: 26
Federal Signal Corporation UltraVoice Installation, Operation And Service Manual preview
UltraVoice
Brand: Federal Signal Corporation Pages: 60
FASTRON. VC-210 Installation And Operating Instructions Manual preview
VC-210
Brand: FASTRON. Pages: 16
ICP DAS USA XP-9 88-IoT Series Quick Start Manual preview
XP-9 88-IoT Series
Brand: ICP DAS USA Pages: 8
EFI E-42 Installation And Service Manual preview
E-42
Brand: EFI Pages: 127
maxxess eMAX-EP4502 Installation Manual preview
eMAX-EP4502
Brand: maxxess Pages: 11
SOLARJACK PVA 5-30 User Manual preview
PVA 5-30
Brand: SOLARJACK Pages: 14
intech 21 OPLC-2100 Operation Manual preview
OPLC-2100
Brand: intech 21 Pages: 15
THOR THPWM-30 Instruction Manual preview
THPWM-30
Brand: THOR Pages: 12
DPS Telecom NetGuardian LPG D-PK-NGLPG User Manual preview
NetGuardian LPG D-PK-NGLPG
Brand: DPS Telecom Pages: 82
SMC Networks ITV 0 Series Instruction Manual preview
ITV 0 Series
Brand: SMC Networks Pages: 2
Cypress AN77960 Manual preview
AN77960
Brand: Cypress Pages: 13
RIFT Actuators RIFT 400 Installation, Operation & Maintenance Instructions Manual preview
RIFT 400
Brand: RIFT Actuators Pages: 23
Troy-Bilt TE31 Series User Manual preview
TE31 Series
Brand: Troy-Bilt Pages: 11
Ubiquiti Raspberry Pi 3B+ UniFi Controller Quick Start Manual preview
Raspberry Pi 3B+ UniFi Controller
Brand: Ubiquiti Pages: 4
HUAYUAN MAM860 Operation Manual preview
MAM860
Brand: HUAYUAN Pages: 17
gefran 1200-RD00-00-0 Series Quick Start Manual preview
1200-RD00-00-0 Series
Brand: gefran Pages: 6

Brands by name

Popular brands

Load more brands