manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 7 Mode Entry Module (MC_ME)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

147

 

7.3.2.7

Debug Mode Transition Status Register (ME_DMTS)

This register provides the status of different factors which influence mode transitions. It is used to give an 
indication of why a mode transition indicated by ME_GS.S_MTRANS may be taking longer than 
expected.

NOTE

The ME_DMTS register does not indicate whether a mode transition is 
ongoing. Therefore, some ME_DMTS bits may still be asserted after the 
mode transition has completed.

S_NMA

Non-existing Mode Access status

 — This bit is set whenever the target mode requested is one of 

those non existing modes determined by ME_ME register. It is cleared by writing a ‘1’ to this bit.
0 Target mode requested is an existing mode
1 Target mode requested is a non-existing mode

S_SEA

SAFE 

Event Active status

 — This bit is set whenever the device is in SAFE mode, SAFE event bit 

is pending and a new mode requested other than RESET/SAFE modes. It is cleared by writing a ‘1’ 
to this bit.
0 No new mode requested other than RESET/SAFE while SAFE event is pending
1 New mode requested other than RESET/SAFE while SAFE event is pending

Address

 

0xC3FD_C018

Access: User read, Supervisor read/write, Test read/write

R

PREVIOUS_MODE

0

0

0

0

MPH_B

U

SY

0

0

PMC_PR

OG

CORE_DBG

0

0

SMR

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

R

0

VREG_CSRC_SC

CSRC_

CSRC_SC

16

 M

H

z_I

R

C_

SC

SCSRC_SC

SYSCLK_SW

DFLASH_SC

CFLASH_SC

CDP_PR

P

H

_0_1

43

0

0

0

0

CDP_PR

P

H

_64_

95

CDP_PR

P

H

_32_

63

CDP_PRPH_

0_31

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 7-8. Debug Mode Transition Status Register (ME_DMTS)

Table 7-9. Invalid Mode Transition Status Register (ME_IMTS) Field Descriptions (continued)

Field

Description

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Kärcher K 3 How To Connect preview
K 3
Brand: Kärcher Pages: 4
Lattice Semiconductor MachXO5-NX Development Kit Quick Start preview
MachXO5-NX Development Kit
Brand: Lattice Semiconductor Pages: 2
Zencontrol zc-controller Instructions preview
zc-controller
Brand: Zencontrol Pages: 2
Daikin KBRCS01A Quick Start Manual preview
KBRCS01A
Brand: Daikin Pages: 2
Advantech PCI-1760U Startup Manual preview
PCI-1760U
Brand: Advantech Pages: 3
R-Tec controlR Installation Manual & User Manual preview
controlR
Brand: R-Tec Pages: 14
Current Mini LOOP BT Quick Start Manual preview
Mini LOOP BT
Brand: Current Pages: 4
PEAS VC-530E User Manual preview
VC-530E
Brand: PEAS Pages: 4
Sollae Systems CIE-M10A User Manual preview
CIE-M10A
Brand: Sollae Systems Pages: 72
PXM DMX DEMUX 8 Manual preview
DMX DEMUX 8
Brand: PXM Pages: 15
ISC APECS Operational Instructions preview
APECS
Brand: ISC Pages: 20
mikroElektronika mikromedia for ARM User Manual preview
mikromedia for ARM
Brand: mikroElektronika Pages: 35
Fisher R622 Instruction Manual preview
R622
Brand: Fisher Pages: 8
ZiLOG S3F8S19 User Manual preview
S3F8S19
Brand: ZiLOG Pages: 23
D+H KA 66-TW-DF Original Instructions Manual preview
KA 66-TW-DF
Brand: D+H Pages: 16
Gira 0425 00 Quick Start Manual preview
0425 00
Brand: Gira Pages: 7
HIMA HIMatrix F31 02 Manual preview
HIMatrix F31 02
Brand: HIMA Pages: 48
Resol DeltaSol SLL Installation, Operation, Maintenance Manual preview
DeltaSol SLL
Brand: Resol Pages: 60

Brands by name

Popular brands

Load more brands