manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 15 Error Correction Status Module (ECSM)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

283

 

15.4.2

Registers description

Attempted accesses to reserved addresses result in an error termination, while attempted writes to 
read-only registers are ignored and do not terminate with an error. Unless noted otherwise, 

writes to the 

programming model must match the size of the register

, e.g., an 

n

-bit register only supports 

n

-bit writes, 

etc. Attempted writes of a different size than the register width produce an error termination of the bus 
cycle and no change to the targeted register.

15.4.2.1

Processor core type (PCT) register

The PCT is a 16-bit read-only register that specifies the architecture of the processor core in the device. 
The state of this register is defined by a module input signal; it can only be read from the IPS programming 
model. Any attempted write is ignored.

15.4.2.2

Revision (REV) register

The REV is a 16-bit read-only register specifying a revision number. The state of this register is defined 
by an input signal; it can only be read from the IPS programming model. Any attempted write is ignored.

0x0066

REMR—RAM ECC Master register

on page 298

8

0x0067

REAT—RAM ECC Attributes register

on page 298

8

0x0068–0x006B

Reserved

0x006C

REDR—RAM ECC Data register

on page 299

32

0x0070–0x3FFF

Reserved

Address: Base + 0x0000

Access: User read-only

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

PCT[15:0]

W

Reset

1

1

1

0

0

0

0

0

0

0

0

1

0

0

1

0

Figure 15-1. Processor core type (PCT) register

Table 15-2. PCT field descriptions

Name

Description

0-15

PCT[15:0]

Processor Core Type
0xE012 identifies the z0H Power Architecture.

Table 15-1. ECSM registers (continued)

Offset from

ECSM_BASE

0xFFF4_0000

Register

Location

Size (bits)

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Gamma Vacuum SPCe User Manual preview
SPCe
Brand: Gamma Vacuum Pages: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Brand: Gamma Pages: 28
YOKOGAWA UTAdvanced UT35A Technical Information preview
UTAdvanced UT35A
Brand: YOKOGAWA Pages: 18
Quantum NE PLUS Basic Operation Instructions preview
NE PLUS
Brand: Quantum Pages: 20
TWR Lighting E-1DB2 Manual preview
E-1DB2
Brand: TWR Lighting Pages: 49
ICP DAS USA ISaGRAF WinCE ViewPAC User Manual preview
ISaGRAF WinCE ViewPAC
Brand: ICP DAS USA Pages: 192
OMEGA AIR AWS-C Instructions Manual preview
AWS-C
Brand: OMEGA AIR Pages: 12
G-Scale Graphics railboss 4 Operation And Installtion Manual preview
railboss 4
Brand: G-Scale Graphics Pages: 12
Belimo GM24A-MOD Technical Data Sheet preview
GM24A-MOD
Brand: Belimo Pages: 6
G-Scale Graphics LSCM2 Operation And Installation Manual preview
LSCM2
Brand: G-Scale Graphics Pages: 7
Texas Instruments TIDA-00830 Quick Start Manual preview
TIDA-00830
Brand: Texas Instruments Pages: 6
Atmel AVR128 Application Note preview
AVR128
Brand: Atmel Pages: 8
Evco EVRS225 Manual preview
EVRS225
Brand: Evco Pages: 10
MICROMATIC A010240 Installation, Service, And Use Manual preview
A010240
Brand: MICROMATIC Pages: 10
Spirax Sarco IP2AM Installation And Maintenance Instructions Manual preview
IP2AM
Brand: Spirax Sarco Pages: 20
Salus PC11W Manual preview
PC11W
Brand: Salus Pages: 2
Intersil ISL6526 Quick Start Manual preview
ISL6526
Brand: Intersil Pages: 8
Micro ID Sdn Bh MZ11D7 Quick Start Manual preview
MZ11D7
Brand: Micro ID Sdn Bh Pages: 7

Brands by name

Popular brands

Load more brands