background image

Technical data sheet

GM24A-MOD

Communicative damper actuator 

for adjusting dampers in technical 

building installations

•  Air damper size up to approx. 8 m²

•  Torque motor 40 Nm

•  Nominal voltage AC/DC 24 V

•  Control modulating, communicative, 

hybrid

•  Conversion of sensor signals

•  Communication via BACnet MS/TP, 

Modbus RTU, Belimo-MP-Bus or 

conventional control

 

Technical data

Electrical data   Nominal voltage

AC/DC 24 V

  Nominal voltage frequency

50/60 Hz

  Nominal voltage range

AC 19.2...28.8 V / DC 21.6...28.8 V

  Power consumption in operation

4 W

  Power consumption in rest position

1.6 W

  Power consumption for wire sizing

7 VA

  Connection supply / control

Cable 1 m, 6 x 0.75 mm²

Functional data   Torque motor

40 Nm

  Torque variable

25%, 50%, 75% reduced

  Communicative control

BACnet MS/TP

Modbus RTU (ex works)

MP-Bus

  Operating range Y

2...10 V

  Operating range Y variable

0.5...10 V

  Position feedback U

2...10 V

  Position feedback U note

Max. 1 mA

  Position feedback U variable

Start point 0.5...8 V

End point 2...10 V

  Position accuracy

±5%

  Direction of motion motor

selectable with switch 0/1

  Direction of motion note

Y = 0%: At switch position 0 (ccw rotation) / 1 

(cw rotation)

  Direction of motion variable

electronically reversible

  Manual override

with push-button, can be locked

  Angle of rotation

Max. 95°

  Angle of rotation note

can be limited on both sides with adjustable 

mechanical end stops

  Running time motor

150 s / 90°

  Running time motor variable

75...290 s

  Adaptation setting range

manual

  Adaptation setting range variable

No action

Adaptation when switched on

Adaptation after pushing the gear 

disengagement button

  Override control, controllable via bus 

communication

MAX (maximum position) = 100%

MIN (minimum position) = 0%

ZS (intermediate position) = 50%

  Override control variable

MAX = (MIN + 32%)...100%

MIN = 0%...(MAX – 32%)

ZS = MIN...MAX

  Sound power level, motor

45 dB(A)

  Mechanical interface

Universal shaft clamp 12...26.7 mm

  Position indication

Mechanically, pluggable

Safety   Protection class IEC/EN

III Safety Extra-Low Voltage (SELV)

  Protection class UL

UL Class 2 Supply

  Degree of protection IEC/EN

IP54

  Degree of protection NEMA/UL

NEMA 2

  Enclosure

UL Enclosure Type 2

  EMC

CE according to 2014/30/EU

www.belimo.com

GM24A-MOD • en-gb • 2020-04-21 • subject to changes

1

Summary of Contents for GM24A-MOD







Reviews: