manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 310

Chapter 17 Flash Memory

MPC5602P Microcontroller Reference Manual, Rev. 4

310

Freescale Semiconductor

 

17.2.4.1

Memory map

First, consider the Flash memory space accessed via transactions from the platform Flash controller’s AHB 
port. To support the two separate Flash memory banks, the platform Flash controller uses address bit 23 
(haddr[23]) to steer the access to the appropriate memory bank. In addition to the actual Flash memory 
regions, there are shadow and test sectors included in the system memory map. The program-visible 
control and configuration registers associated with each memory array are included in the slave peripheral 
address region. The system memory map defines one code Flash array and one data Flash array. See 

Table 17-1

.

CAUTION

Software executing from flash memory must not write to registers that 
control flash behavior (such as wait state settings or prefetch 
enable/disable). Doing so can cause data corruption. On this chip, these 
registers include PFCR0 and PFAPR.

NOTE

Flash memory configuration registers should be written only with 32-bit 
write operations to avoid any issues associated with register incoherency 
caused by bit fields spanning smaller size (8-, 16-bit) boundaries.

For additional information on the address-based read access timing for emulation of other memory types, 
see 

Section 17.2.17, “Wait state emulation.

Table 17-1. Flash-related regions in the system memory map

Start address

End address

Size 

(KB)

Region

0x0000_0000

0x0007_FFFF

512

Code Flash array 0

0x0008_0000

0x001F_FFFF

1536

Reserved

0x0020_0000

0x0020_3FFF

16

Code Flash array 0: shadow sector

0x0020_4000

0x003F_FFFF

2032

Reserved

0x0040_0000

0x0040_3FFF

16

Code Flash array 0: test sector

0x0040_4000

0x007F_FFFF

4080

Reserved

0x0080_0000

0x0080_FFFF

64

Data Flash array 0

0x0081_0000

0x00C0_1FFF

4040

Reserved 

0x00C0_2000

0x00C0_3FFF

8

Data Flash array 0: test sector

0x00C0_4000

0x00FF_FFFF

4080

Reserved

0x0100_0000

0x1FFF_FFFF

507904

Emulation Mapping

0xFFE8_8000

0xFFE8_BFFF

16

Code Flash array 0 configuration

1

1

This region is also aliased to address 0xC3F8_nnnn.

0xFFE8_C000

0xFFE8_FFFF

16

Data Flash array 0 configuration

1

0xFFEB_0000

0xFFEB_BFFF

48

Reserved

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands