manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 22 FlexCAN

MPC5602P Microcontroller Reference Manual, Rev. 4

552

Freescale Semiconductor

 

22.3.4.4

Rx Global Mask register (RXGMASK)

This register is provided for legacy support and for low cost MCUs that do not have the individual masking 
per Message Buffer feature. For MCUs supporting individual masks per MB, setting the BCC bit in the 
MCR causes the RXGMASK register to have no effect on the module operation. For MCUs not supporting 
individual masks per MB, this register is always effective.

RXGMASK is used as an acceptance mask for all Rx MBs, excluding MBs 14

–

15, which have individual 

mask registers. When the FEN bit in the MCR is set (FIFO enabled), the RXGMASK also applies to all 
elements of the ID filter table, except elements 6–7, which have individual masks.

The contents of this register must be programmed while the module is in Freeze Mode, and must not be 
modified when the module is transmitting or receiving frames.

22.3.4.5

Rx 14 Mask (RX14MASK)

This register is provided for legacy support and for low cost MCUs that do not have the individual masking 
per Message Buffer feature. For MCUs supporting individual masks per MB, setting the BCC bit in the 
MCR causes the RX14MASK register to have no effect on the module operation.

RX14MASK is used as an acceptance mask for the Identifier in Message Buffer 14. When the FEN bit in 
the MCR is set (FIFO enabled), the RX14MASK also applies to element 6 of the ID filter table. This 

Table 22-14. TIMER field descriptions

Field

Description

TIMER

Holds the value for this timer.

Address: Base + 0x0010

Access: User read/write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

MI31 MI30 MI29 MI28 MI27 MI26 MI25 MI24 MI23 MI22 MI21 MI20 MI19 MI18 MI17 MI16

W

Reset

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

MI15 MI14 MI13 MI12 MI11 MI10

MI9

MI8

MI7

MI6

MI5

MI4

MI3

MI2

MI1

MI0

W

Reset

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Figure 22-7. Rx Global Mask register (RXGMASK)

Table 22-15. RXGMASK field description

Field

Description

0–31

MI31–MI0

Mask Bits
For normal Rx MBs, the mask bits affect the ID filter programmed on the MB. For the Rx FIFO, the 
mask bits affect all bits programmed in the filter table (ID, IDE, RTR).
0 The corresponding bit in the filter is “don’t care.”
1 The corresponding bit in the filter is checked against the one received. 

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

H3C WX Series Configuration Manual preview
WX Series
Brand: H3C Pages: 69
EasyIO FG-20 Installation Manual preview
FG-20
Brand: EasyIO Pages: 17
ICP DAS USA XP-9 88-IoT Series Quick Start Manual preview
XP-9 88-IoT Series
Brand: ICP DAS USA Pages: 8
Wavelength Electronics PTC5000 Datasheet And Operating Manual preview
PTC5000
Brand: Wavelength Electronics Pages: 17
4IPNET WHG301 Quick Installation Manual preview
WHG301
Brand: 4IPNET Pages: 11
Lennox HYDROCONTROL Installation, Operating And Maintenance Manual preview
HYDROCONTROL
Brand: Lennox Pages: 34
Rohde ST 630 Operation Manual preview
ST 630
Brand: Rohde Pages: 344
SAMES KREMLIN LP 6 - 0.5/4 Translation From The Original Manual preview
LP 6 - 0.5/4
Brand: SAMES KREMLIN Pages: 5
NEC V850E/RS1 User Manual preview
V850E/RS1
Brand: NEC Pages: 852
Daktronics All Sport 1600 Series Operation Manual preview
All Sport 1600 Series
Brand: Daktronics Pages: 92
Taconova TACOTHERM FRESH PETA ES 5941S Manual preview
TACOTHERM FRESH PETA ES 5941S
Brand: Taconova Pages: 40
MAKELSAN MRG33 Series User Manual preview
MRG33 Series
Brand: MAKELSAN Pages: 28
Unika PR-1V Operation Manual preview
PR-1V
Brand: Unika Pages: 4
M5Stack FIRE Quick Start Manual preview
FIRE
Brand: M5Stack Pages: 6
Spektrum FC6250HX Manual preview
FC6250HX
Brand: Spektrum Pages: 20
Jetter JC-975MC Installation Manual preview
JC-975MC
Brand: Jetter Pages: 28
Wecon LX3V-4AD User Manual preview
LX3V-4AD
Brand: Wecon Pages: 12
BBB MICRO System User Manual preview
MICRO System
Brand: BBB Pages: 14

Brands by name

Popular brands

Load more brands