manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 916

Chapter 36 Nexus Development Interface (NDI)

MPC5602P Microcontroller Reference Manual, Rev. 4

916

Freescale Semiconductor

 

11

I_DVLE

1

Instruction Side Debug TLB ‘VLE’ Attribute Bit (I_DVLE) 
This bit is used to provide the ‘VLE’ attribute bit to be used when the MMU is disabled during 
a debug session.

12

I_DI

1

Instruction Side Debug TLB ‘I’ Attribute Bit (I_DI) 
This bit is used to provide the ‘I’ attribute bit to be used for Instruction accesses when the 
MMU is disabled for Instruction accesses during a debug session.

13

I_DM

1

Instruction Side Debug TLB ‘M’ Attribute Bit (I_DM) 
This bit is used to provide the ‘M’ attribute bit to be used for Instruction accesses when the 
MMU is disabled for Instruction accesses during a debug session.

14

—

Reserved

15

I_DE

1

Instruction Side Debug TLB ‘E’ Attribute Bit (I_DE) 
This bit is used to provide the ‘E’ attribute bit to be used for Instruction accesses when the 
MMU is disabled for Instruction accesses during a debug session.

16

D_DMDIS

1

Data Side Debug MMU Disable Control Bit (D_DMDIS) 
0 – MMU not disabled for debug sessions
1 – MMU disabled for debug sessions
This bit may be used to control whether the MMU is enabled normally, or whether the MMU 
is disabled during a debug session for Data Accesses. When enabled, the MMU functions 
normally. When disabled, for Data Accesses, no address translation is performed (1:1 
address mapping), and the TLB WIMGE bits are taken from the OCR bits D_DW, D_DI, 
D_DM, D_DG, and D_DE bits. The SR, SW, UR, and UW access permission control bits are 
set to‘1’ to allow full access. When disabled, no TLB miss or TLB exceptions are generated 
for Data accesses. External access errors can still occur.

17:18

—

Reserved

19

D_DW

1

Data Side Debug TLB ‘W’ Attribute Bit (D_DW) 
This bit is used to provide the ‘W’ attribute bit to be used for Data accesses when the MMU 
is disabled for Data accesses during a debug session.

20

D_DI

1

Data Side Debug TLB ‘I’ Attribute Bit (D_DI) 
This bit is used to provide the ‘I’ attribute bit to be used for Data accesses when the MMU is 
disabled for Data accesses during a debug session.

21

D_DM

1

Data Side Debug TLB ‘M’ Attribute Bit (D_DM) 
This bit is used to provide the ‘M’ attribute bit to be used for Data accesses when the MMU 
is disabled for Data accesses during a debug session.

22

D_DG

1

Data Side Debug TLB ‘G’ Attribute Bit (D_DG) 
This bit is used to provide the ‘G’ attribute bit to be used for Data accesses when the MMU is 
disabled for Data accesses during a debug session.

23

D_DE

1

Data Side Debug TLB ‘E’ Attribute Bit (D_DE) 
This bit is used to provide the ‘E’ attribute bit to be used for Data accesses when the MMU is 
disabled for Data accesses during a debug session.

24:28

—

Reserved

Table 36-13. OnCE Control Register Bit Definitions (continued)

Bit(s)

Name

Description

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands