manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 1 Introduction

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

35

 

Chapter 1  
Introduction

1.1

The MPC5602P microcontroller family

The Qorivva MPC5602P microcontroller, a SafeAssure solution, is built on the Power Architecture

®

 

platform. The Power Architecture

 

based 32-bit microcontrollers represent the latest achievement in 

integrated automotive application controllers. This device family integrates the most advanced and 
up-to-date motor control design features.

The safety features included in MPC5602P (such us fault collection unit, safety port or flash memory and 
SRAM with ECC) support the design of system applications where safety is a requirement.

The MPC5602P addresses low-end chassis applications and implements the Harvard bus interface version 
of the e200z0h core.

The e200 processor family is a set of CPU cores that implement low-cost versions of the Power 
Architecture Book E architecture. The e200 processors are designed for deeply embedded control 
applications that require low cost solutions rather than maximum performance. The e200z0h processor 
integrates an integer execution unit, branch control unit, instruction fetch and load/store units, and a 
multi-ported register file capable to sustaining three read and two write operations per clock. Most integer 
instructions execute in a single clock cycle. Branch target prefetching is performed by branch unit to allow 
single-cycle branches in some cases. The e200z0h core is a single-issue, 32-bit Power Architecture 
technology VLE only design with 32-bit general purpose registers (GPRs). All arithmetic instructions that 
execute in the core operate on data in the general purpose registers (GPRs). Instead of the base Power 
Architecture instruction set support, the e200z0h core only implements the VLE (variable length 
encoding) APU, providing improved code density.

The MPC5602P has a single level of memory hierarchy consisting of 20 KB on-chip SRAM and 320 KB 
(256 KB p 64 KB data) of on-chip flash memory. Both the SRAM and the flash memory can hold 
instructions and data.

The timer functions of the MPC5602P are performed by the eTimer Modular Timer System and 
FlexPWM. The eTimer module implements enhanced timer features (six channels) including dedicated 
motor control quadrature decode functionality and DMA support; the FlexPWM module consists of four 
submodules controlling a pair of PWM channels each: three submodules may be used to control the three 
phases of a motor and the additional pair to support DC-DC converter width modulation control.

Off-chip communication is performed by a suite of serial protocols including CANs, enhanced SPIs 
(DSPI), and SCIs (LINFlex).

The System Integration Unit Lite (SIUL) performs several chip-wide configuration functions. Pad 
configuration and general-purpose input/output (GPIO) are controlled from the SIUL. External interrupts 
and reset control are also found in the SIUL. The internal multiplexer sub-block (IOMUX) provides 
multiplexing of daisy chaining the DSPIs and external interrupt signal.

As the MPC5602P is built on a wider legacy of Power Architecture-based devices, when applicable and 
possible, reuse or enhancement of existing IP, design and concepts is adopted.

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

ZKTeco SC800 User Manual preview
SC800
Brand: ZKTeco Pages: 123
LANGER EMV-Technik E 1 User Manual preview
E 1
Brand: LANGER EMV-Technik Pages: 48
Talgil DREAM 2 Manual preview
DREAM 2
Brand: Talgil Pages: 14
National Instruments NI 9514 User Manual preview
NI 9514
Brand: National Instruments Pages: 72
mikroElektronika mikromedia for ARM User Manual preview
mikromedia for ARM
Brand: mikroElektronika Pages: 35
IBM ServeRAID M1215 SAS User Manual preview
ServeRAID M1215 SAS
Brand: IBM Pages: 35
B&K Reference 20 Plus A/V System Controller Owner'S Manual preview
Reference 20 Plus A/V System Controller
Brand: B&K Pages: 84
Fego Precision Industrial TP48 Instructions preview
TP48
Brand: Fego Precision Industrial Pages: 2
XICOY LGC 13C User Manual preview
LGC 13C
Brand: XICOY Pages: 10
Vitto Fingerprint Series User Manual preview
Fingerprint Series
Brand: Vitto Pages: 9
K-Tech ET901 Programming Manual preview
ET901
Brand: K-Tech Pages: 2
DSE DSE7110 MKII Operator'S Manual preview
DSE7110 MKII
Brand: DSE Pages: 100
TJERNLUND MAC4E CONTROL VERSION F (COMPATIBLE WITH UC1 CONTROL) 8504112 REV B 0805 Operating And Mounting Instructions preview
MAC4E CONTROL VERSION F (COMPATIBLE WITH UC1 CONTROL) 8504112 REV B 0805
Brand: TJERNLUND Pages: 2
suprema BioStation 3 Installation Manual preview
BioStation 3
Brand: suprema Pages: 41
FAAC 424 D LS Instructions For Use Manual preview
424 D LS
Brand: FAAC Pages: 14
H3C WX2540H Installation Manual preview
WX2540H
Brand: H3C Pages: 40
Emerson EL-O-MATIC EL100 Reference Manual preview
EL-O-MATIC EL100
Brand: Emerson Pages: 32
Emerson EIM TEC2 500 Quick Start Manual preview
EIM TEC2 500
Brand: Emerson Pages: 18

Brands by name

Popular brands

Load more brands