manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 25 FlexPWM

MPC5602P Microcontroller Reference Manual, Rev. 4

678

Freescale Semiconductor

 

25.6.5.2

Fault Status Register (FSTS)

Table 25-18. FCTRL field descriptions

Field

Description

0:3

FLVL

Fault Level
These read/write bits select the active logic level of the individual fault inputs. A reset clears FLVL.
0 A logic 0 on the fault input indicates a fault condition.
1 A logic 1 on the fault input indicates a fault condition.

4:7

FAUTO

Automatic Fault Clearing
These read/write bits select automatic or manual clearing of faults. A reset clears FAUTO.
0 Manual fault clearing. PWM outputs disabled by this fault are not enabled until the FFLAGx bit is 

clear at the start of a half cycle. This is further controlled by the FSAFE bits.

1 Automatic fault clearing. PWM outputs disabled by this fault are enabled when the FFPINx bit is 

clear at the start of a half cycle without regard to the state of FFLAGx bit.

8:11

FSAFE

Fault Safety Mode
These read/write bits select the safety mode during manual fault clearing. A reset clears FSAFE.
0 Normal mode. PWM outputs disabled by this fault are not enabled until the FFLAGx bit is clear at 

the start of a half cycle without regard to the state of the FFPINx bit. The PWM outputs disabled 
by this fault input will not be re-enabled until the actual FAULTx input signal de-asserts since the 
fault input will combinationally disable the PWM outputs (as programmed in DISMAP).

1 Safe mode. PWM outputs disabled by this fault are not enabled until the FFLAGx bit is clear and 

the FFPINx bit is clear at the start of a half cycle.

Note:

The FFPINx bit may indicate a fault condition still exists even though the actual fault signal at 
the FAULTx pin is clear due to the fault filter latency.

12:15

FIE

Fault Interrupt Enables
This read/write bit enables CPU interrupt requests generated by the FAULTx pins. A reset clears FIE.
0 FAULTx CPU interrupt requests disabled.
1 FAULTx CPU interrupt requests enabled.

Note:

The fault protection circuit is independent of the FIEx bit and is always active. If a fault is 
detected, the PWM outputs are disabled according to the disable mapping register.

Address: Base + 0x014E

Access: User read/write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

FTEST

FFPIN

0

0

0

0

FFLAG

W

Reset

0

0

0

0

0

0

1

1

0

0

0

0

0

0

1

1

Figure 25-27. Fault Status Register (FSTS)

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Caen V793 Technical Information Manual preview
V793
Brand: Caen Pages: 20
Danfoss ERC 211 User Manual preview
ERC 211
Brand: Danfoss Pages: 36
IFM EC2121 System Manual preview
EC2121
Brand: IFM Pages: 41
ZKTeco LockerPad-7B User Manual preview
LockerPad-7B
Brand: ZKTeco Pages: 27
Sunlight Supply TITAN CONTROLS KRONUS 2 Instruction Manual preview
TITAN CONTROLS KRONUS 2
Brand: Sunlight Supply Pages: 4
E+L RK 4004 Manual preview
RK 4004
Brand: E+L Pages: 62
Omicron BETA 9.2 Quick Start Manual preview
BETA 9.2
Brand: Omicron Pages: 17
Simplex RTL-TH DIGITAL Installation And Operating Instructions Manual preview
RTL-TH DIGITAL
Brand: Simplex Pages: 12
3M Touch Screen Controller EX112 Reference Manual preview
Touch Screen Controller EX112
Brand: 3M Pages: 40
Brooks 5851EM Series Installation And Operation Manual preview
5851EM Series
Brand: Brooks Pages: 62
Mono DELTA DEPOSITOR Operation Manual preview
DELTA DEPOSITOR
Brand: Mono Pages: 60
MDT AMI series Technical Manual preview
AMI series
Brand: MDT Pages: 51
Belimo LMC230 Manual preview
LMC230
Brand: Belimo Pages: 10
Dontek V7-RTS Instructions Manual preview
V7-RTS
Brand: Dontek Pages: 10
HUAYUAN MAM860 Operation Manual preview
MAM860
Brand: HUAYUAN Pages: 17
Integra 155000 Operating Instructions Manual preview
155000
Brand: Integra Pages: 17
3Ware 8006-2LP - Escalade RAID Controller Manual preview
8006-2LP - Escalade RAID Controller
Brand: 3Ware Pages: 126
M-system SC100 Series User Manual preview
SC100 Series
Brand: M-system Pages: 24

Brands by name

Popular brands

Load more brands