manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 20 Deserial Serial Peripheral Interface (DSPI)

MPC5602P Microcontroller Reference Manual, Rev. 4

482

Freescale Semiconductor

 

20.9.3

Delay settings

Table 20-28

 shows the values for the delay after transfer (t

DT

) and CS to SCK delay (t

CSC

) that can be 

generated based on the prescaler values and the scaler values set in the DSPI

x

_CTARs. The values 

calculated assume a 100 MHz system frequency.

20.9.4

MPC5602P DSPI compatibility with QSPI of the MPC500 MCUs

Table 20-29

 shows the translation of commands written to the TX FIFO command halfword with 

commands written to the command RAM of the MPC500 family MCU QSPI. The table illustrates how to 
configure the DSPI

x

_CTARs to match the default cases for the possible combinations of the MPC500 

family control bits in its command RAM. The defaults for the QSPI are based on a system clock of 40 
MHz. 

Table 20-28. Delay values

Delay prescaler values

(DSPI_CTAR[PBR])

1

3

5

7

Dela

y

 s

caler v

a

lues (DSPI_CT

AR[DT])

2

20.0 ns

60.0 ns

100.0 ns

140.0 ns

4

40.0 ns

120.0 ns

200.0 ns

280.0 ns

8

80.0 ns

240.0 ns

400.0 ns

560.0 ns

16

160.0 ns

480.0 ns

800.0 ns

1.1 

s

32

320.0 ns

960.0 ns

1.6 

s

2.2 

s

64

640.0 ns

1.9 

s

3.2 

s

4.5 

s

128

1.3 

s

3.8 

s

6.4 

s

9.0 

s

256

2.6 

s

7.7 

s

12.8 

s

17.9 

s

512

5.1 

s

15.4 

s

25.6 

s

35.8 

s

1024

10.2 

s

30.7 

s

51.2 

s

71.7 

s

2048

20.5 

s

61.4 

s

102.4 

s

143.4 

s

4096

41.0 

s

122.9 

s

204.8 

s

286.7 

s

8192

81.9 

s

245.8 

s

409.6 

s

573.4 

s

16384

163.8 

s

491.5 

s

819.2 

s

1.1 ms

32768

327.7 

s

983.0 

s

1.6 ms

2.3 ms

65536

655.4 

s

2.0 ms

3.3 ms

4.6 ms

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Brand: Panasonic Pages: 45
Panasonic Minas A4 Series Connection Manual preview
Minas A4 Series
Brand: Panasonic Pages: 5
Danfoss VLT 2800 Instruction Manual preview
VLT 2800
Brand: Danfoss Pages: 7
Samson 3277 Quick Manual preview
3277
Brand: Samson Pages: 2
Oceanic DX1 Product Service Manual preview
DX1
Brand: Oceanic Pages: 11
Panosol SR658 Operation Manuals preview
SR658
Brand: Panosol Pages: 105
Pangolin FB4 Series Quick Start Manual preview
FB4 Series
Brand: Pangolin Pages: 8
xpr VPROX2-M User Manual preview
VPROX2-M
Brand: xpr Pages: 4
Rain Bird ESP-RZXe Installation And Operation Manual preview
ESP-RZXe
Brand: Rain Bird Pages: 18
Olsen 58468 Owner'S Manual & Safety Instructions preview
58468
Brand: Olsen Pages: 4
Woodward ProAct III Installation And Operation Manual preview
ProAct III
Brand: Woodward Pages: 32
Carel EVD mini User Manual preview
EVD mini
Brand: Carel Pages: 36
Fairford Synergy SGY-101 Quick Start Manual preview
Synergy SGY-101
Brand: Fairford Pages: 20
ST UM1932 User Manual preview
UM1932
Brand: ST Pages: 40
Varian 969-9507 Instruction Manual preview
969-9507
Brand: Varian Pages: 37
Oriental motor ASD10A-K Operating Manual preview
ASD10A-K
Brand: Oriental motor Pages: 52
Opt OPT-DPA1024E-4 Manual preview
OPT-DPA1024E-4
Brand: Opt Pages: 40
Zamel exta life SRM-22 Operation Manual preview
exta life SRM-22
Brand: Zamel Pages: 5

Brands by name

Popular brands

Load more brands