manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 454

Chapter 20 Deserial Serial Peripheral Interface (DSPI)

MPC5602P Microcontroller Reference Manual, Rev. 4

454

Freescale Semiconductor

 

3

EOQF

End of queue flag
Indicates that transmission in progress is the last entry in a queue. The EOQF bit is set when the 
TX FIFO entry has the EOQ bit set in the command halfword and after the last incoming databit is 
sampled, but before the tASC delay starts. Refer to 

Section 20.8.5.1, “Classic SPI transfer format 

(CPHA = 0)

 for details. 

The EOQF bit is cleared by writing 1 to it. When the EOQF bit is set, the TXRXS bit is automatically 
cleared.
0 EOQ is not set in the executing command. 
1 EOQ bit is set in the executing SPI command. 

Note:

EOQF does not function in slave mode. 

4

TFUF

Transmit FIFO underflow flag
Indicates that an underflow condition in the TX FIFO has occurred. The transmit underflow 
condition is detected only for DSPI modules operating in slave mode and SPI configuration. The 
TFUF bit is set when the TX FIFO of a DSPI operating in SPI slave mode is empty, and a transfer 
is initiated by an external SPI master. The TFUF bit is cleared by writing 1 to it.
0 TX FIFO underflow has not occurred.
1 TX FIFO underflow has occurred.

5

Reserved

6

TFFF

Transmit FIFO fill flag
Indicates that the TX FIFO can be filled. Provides a method for the DSPI to request more entries to 
be added to the TX FIFO. The TFFF bit is set while the TX FIFO is not full. The TFFF bit can be 
cleared by writing 1 to it, or an by acknowledgement from the eDMA controller when the TX FIFO 
is full.
0 TX FIFO is full.
1 TX FIFO is not full.

7–11

Reserved

12

RFOF

Receive FIFO overflow flag
Indicates that an overflow condition in the RX FIFO has occurred. The bit is set when the RX FIFO 
and shift register are full and a transfer is initiated. The bit is cleared by writing 1 to it.
0 RX FIFO overflow has not occurred.
1 RX FIFO overflow has occurred.

13

Reserved 

14

RFDF

Receive FIFO drain flag
Indicates that the RX FIFO can be drained. Provides a method for the DSPI to request that entries 
be removed from the RX FIFO. The bit is set while the RX FIFO is not empty. The RFDF bit can be 
cleared by writing 1 to it, or by acknowledgement from the eDMA controller when the RX FIFO is 
empty.
0 RX FIFO is empty.
1 RX FIFO is not empty.

Note:

In the interrupt service routine, RFDF must be cleared only after the DSPIx_POPR register 
is read. 

15

Reserved

16–19

TXCTR

[0:3]

TX FIFO counter
Indicates the number of valid entries in the TX FIFO. The TXCTR is incremented every time the 
DSPI _PUSHR is written. The TXCTR is decremented every time an SPI command is executed and 
the SPI data is transferred to the shift register.

Table 20-12. DSPI

x

_SR field descriptions (continued)

Field

Description

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands