manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 7 Mode Entry Module (MC_ME)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

163

 

7.4.2.6

HALT0 Mode

The device enters this mode on the following events:

•

from one of the RUN0…3 modes when the TARGET_MODE bit field of the ME_MCTL register 
is written with “1000”.

As soon as any of the above events has occurred, a HALT0 mode transition request is generated. The mode 
configuration information for this mode is provided by ME_HALT0_MC register. This mode is quite 
configurable, and the ME_HALT0_MC register should be programmed according to the system needs. 
The flashes can be put in low-power or power-down mode as needed. If there is a HALT0 mode request 
while an interrupt request is active, the transition to HALT0 is aborted with the resultant mode being the 
current mode, SAFE (on SAFE mode request), or DRUN (on reset), and an invalid mode interrupt is not 
generated.

This mode is intended as a first-level low-power mode with

•

the core clock frozen

•

only a few peripherals running

and to be used by software

•

to wait until it is required to do something and then to react quickly (i.e., within a few system clock 
cycles of an interrupt event)

7.4.2.7

STOP0 Mode

The device enters this mode on the following events:

•

from one of the RUN0…3 modes when the TARGET_MODE bit field of the ME_MCTL register 
is written with “1010”.

As soon as any of the above events has occurred, a STOP0 mode transition request is generated. The mode 
configuration information for this mode is provided by the ME_STOP0_MC register. This mode is fully 
configurable, and the ME_STOP0_MC register should be programmed according to the system needs. The 
following clock sources are switched off in this mode:

•

the system PLL

The flashes can be put in power-down mode as needed. If there is a STOP0 mode request while any 
interrupt or wakeup event is active, the transition to STOP0 is aborted with the resultant mode being the 
current mode, SAFE (on SAFE mode request), or DRUN (on reset), and an invalid mode interrupt is not 
generated.

This can be used as an advanced low-power mode with the core clock frozen and almost all peripherals 
stopped.

This mode is intended as an advanced low-power mode with

•

the core clock frozen

•

almost all peripherals stopped

and to be used by software

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

ZKTeco PA10 Quick Start Manual preview
PA10
Brand: ZKTeco Pages: 8
EasyIO FT Series User Reference preview
FT Series
Brand: EasyIO Pages: 18
UCS CAT Quick Start Manual preview
CAT
Brand: UCS Pages: 4
Uclear Motion Series User Manual preview
Motion Series
Brand: Uclear Pages: 40
S&C IntelliCap Operation preview
IntelliCap
Brand: S&C Pages: 26
Samson 3371 Series Mounting And Operating Instructions preview
3371 Series
Brand: Samson Pages: 70
Mold-Masters TempMaster M2 Plus Series Quick Manual preview
TempMaster M2 Plus Series
Brand: Mold-Masters Pages: 2
Trinamic TMCM-1240 Hardware Manual preview
TMCM-1240
Brand: Trinamic Pages: 30
turck CODESYS 3 Getting Started preview
CODESYS 3
Brand: turck Pages: 45
Srne ML4860N15 User Manual preview
ML4860N15
Brand: Srne Pages: 13
WAGO 750-872 Quick Start Manual preview
750-872
Brand: WAGO Pages: 44
Rain Bird RC-4Bi Instruction Manual preview
RC-4Bi
Brand: Rain Bird Pages: 7
HomeMatic HM-Sec-SFA-SM Installation And Operating Manual preview
HM-Sec-SFA-SM
Brand: HomeMatic Pages: 38
Advanced Control Technologies th104 Installation Instructions preview
th104
Brand: Advanced Control Technologies Pages: 3
ADLINK Technology cPCI-7252 User Manual preview
cPCI-7252
Brand: ADLINK Technology Pages: 54
Hanbay RD-AC Series User Manual preview
RD-AC Series
Brand: Hanbay Pages: 13
Gigarise SetPro MV Series Instruction Manual preview
SetPro MV Series
Brand: Gigarise Pages: 18
POLA HD38 Handbook preview
HD38
Brand: POLA Pages: 7

Brands by name

Popular brands

Load more brands