manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 8 Reset Generation Module (MC_RGM)

MPC5602P Microcontroller Reference Manual, Rev. 4

188

Freescale Semiconductor

 

8.3.1.6

Functional Event Short Sequence Register (RGM_FESS)

This register defines which reset sequence will be done when a functional reset sequence is triggered. The 
functional reset sequence can either start from PHASE1 or from PHASE3, skipping PHASE1 and 
PHASE2.

NOTE

This could be useful for fast reset sequence, for example to skip flash reset.

It can be accessed in read/write in either supervisor mode or test mode. It can be accessed in read in user 
mode.

AR_CMU0_OLR

Alternate Request for oscillator frequency lower than reference

0 Generate a SAFE mode request on a oscillator frequency lower than reference event if the 

reset is disabled

1 Generate an interrupt request on a oscillator frequency lower than reference event if the reset 

is disabled

AR_PLL0

Alternate Request for PLL0 fail

0 Generate a SAFE mode request on a PLL0 fail event if the reset is disabled
1 Generate an interrupt request on a PLL0 fail event if the reset is disabled

AR_CORE

Alternate Request for core reset

0 Generate a SAFE mode request on a core reset event if the reset is disabled
1 Generate an interrupt request on a core reset event if the reset is disabled

AR_JTAG

Alternate Request for JTAG initiated reset

0 Generate a SAFE mode request on a JTAG initiated reset event if the reset is disabled
1 Generate an interrupt request on a JTAG initiated reset event if the reset is disabled

Address 0xC3FE_4018

Access: User read, Supervisor read/write, Test read/write

R

SS_EXR

0

0

0

0

0

SS_PLL1

SS_FLASH

SS_L

V

D45

SS_

CMU0_FHL

SS_CMU0_

O

L

R

SS_PLL0

SS_CHKST

OP

SS_SOFT

SS_

CORE

SS

_JT

A

G

W

POR

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 8-7. Functional Event Short Sequence Register (RGM_FESS)

Table 8-7. Functional Event Alternate Request Register (RGM_FEAR) Field Descriptions (continued)

Field

Description

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Samson 430 Series Mounting And Operating Instructions preview
430 Series
Brand: Samson Pages: 78
Rachio 3 Get Started preview
3
Brand: Rachio Pages: 16
D-Link DWC-2000 Cli Reference Manual preview
DWC-2000
Brand: D-Link Pages: 113
D-Link DWC-1000 Reference Manual preview
DWC-1000
Brand: D-Link Pages: 146
IAI Msep First Step Manual preview
Msep
Brand: IAI Pages: 5
Nabco Opus Control Installation Manual preview
Opus Control
Brand: Nabco Pages: 35
Madas RG/2MT X Series Technical Manual preview
RG/2MT X Series
Brand: Madas Pages: 28
Rose electronics UltraVista 4K VWL-T122-4K-DP Installation And Operation Manual preview
UltraVista 4K VWL-T122-4K-DP
Brand: Rose electronics Pages: 28
PRECISION DIGITAL PD6200 Instruction Manual preview
PD6200
Brand: PRECISION DIGITAL Pages: 96
HomeMatic HmIP-FAL24-C6 Installation Instructions And Operating Manual preview
HmIP-FAL24-C6
Brand: HomeMatic Pages: 80
Smartgen HMU8-860 User Manual preview
HMU8-860
Brand: Smartgen Pages: 50
Samson TROVIS 5179 Mounting And Operating Instructions preview
TROVIS 5179
Brand: Samson Pages: 142
Hubbell Electric Fire Pump Controllers LXi 2100 Specifications preview
Electric Fire Pump Controllers LXi 2100
Brand: Hubbell Pages: 2
OMC AP23 Installation, Operation And Maintenance Manual preview
AP23
Brand: OMC Pages: 12
ICP DAS USA ACS-11P-MF Quick Start Manual preview
ACS-11P-MF
Brand: ICP DAS USA Pages: 8
Bartec 07-3400 Series Operational Instructions preview
07-3400 Series
Brand: Bartec Pages: 8
Emerson Fisher S202 Instruction Manual preview
Fisher S202
Brand: Emerson Pages: 8
Emerson FISHER SR8 Installation Manual preview
FISHER SR8
Brand: Emerson Pages: 4

Brands by name

Popular brands

Load more brands